登录
首页 » SCM » 6416led+ds1302+8951电子钟,完整源代码

6416led+ds1302+8951电子钟,完整源代码

于 2022-01-25 发布 文件大小:63.39 kB
0 175
下载积分: 2 下载次数: 1

代码说明:

6416led+ds1302+8951电子钟,完整源代码-6416led+ Ds1302+ 8951 email钟Chang, Tai-complete entire Tungsten measurements

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论


0 个回复

  • 用于CAN源代码.rar的头文件,一个不错的例程.
    用于CAN源代码.rar的头文件,一个不错的例程.-for source code. Rar the first document, a pretty good routine.
    2022-07-17 18:01:27下载
    积分:1
  • IO型单片机使用手册
    IO型单片机使用手册-IO-SCM Manuals
    2022-02-10 05:10:20下载
    积分:1
  • 2022-04-16 11:50:29下载
    积分:1
  • 上位机采用vb编程,实现与多台s7200的自由口通信.
    上位机采用vb编程,实现与多台s7200的自由口通信.-Host computer using vb programming, with more than the freedom of the mouth communication s7200.
    2022-04-11 01:57:06下载
    积分:1
  • * Hardware architecture: PA0
    * 硬件结构: PA0-5对应6个LED数显管的位 ,PC0-7对应各LED数显管的段 ,PB4-7为键盘。 * 软件描述: 上电后,时钟从00.00.00(时/分/秒)自动走时,在走时状态时 , 按PB4(设定 * 键)超过3秒可循环选择调整时间/工作参数 ,接着按PB5以确定选择的操作 ,进入调整操作后 , * 按PB5选择欲调整参数,按PB6(增加键)完成调整参数操作 。按PB7,进入时控运行,PB1亮, * 再按PB7停止时控运行,回显走时。在定时到时,PB0点亮。- * Hardware architecture: PA0-5 corresponds 6 LED numbers to reveal the tube the position, PC0-7 corresponds each LED number to reveal the tube the section, PB4-7 is a keyboard. * Software description: After on electricity, clock from 00.00.00 (when/a minute/second) is in luck automatically, when is in luck the condition, according to PB4 (hypothesis * The key) surpasses for 3 seconds to be possible to circulate the choice time/operational parameter, then presses PB5 by to determine the choice the operation, after enters the adjustment operation * Wants according to the PB5 choice to adjust the parameter, (increases key) according to PB6 to complete the adjustment parameter operation.According to PB7, enters when controls the mov
    2022-04-16 19:29:12下载
    积分:1
  • Master and Slave Example Protocol Design for mcs
    Master and Slave Example Protocol Design for mcs-51 keil c51
    2023-07-30 18:20:03下载
    积分:1
  • 单片机RS232/RS485串行发送实验(双机通讯)。 实验步骤: (1),准备两台598K实验机,确定1号机为发送,2号机为接收;...
    单片机RS232/RS485串行发送实验(双机通讯)。 实验步骤: (1),准备两台598K实验机,确定1号机为发送,2号机为接收; (2),当作RS232接口实验时,1号机和2号机的P3.0和P3.1交叉相连,且两机共地; (3),当作RS485接口实验时,1号机和2号机的A、B作对应连接,同时1,2号机的R/TEN接P1.0, P3.0接R0, P3.1接DI。 (4),先运行2号机,键入[27]-->[EV]使2号机处于接收状态P。,后运行1号机[26]-->[EV]使1号机处于发送状态,P。会闪烁,在1号机键盘上按动数字键,在2号机的数码管上应显示对应的数字键值。-Send Singlechip RS232/RS485 serial experiment (two-plane communications). Experimental steps: (1), prepare two sets of experiments 598K machine, determined on the 1st machine to send, on the 2nd machine to receive (2), as a RS232 interface experiment, on the 1st and the 2nd machine and P3.0 P3.1 cross-linked, and the two planes were to (3), as a RS485 interface experiment, on the 1st and the 2nd machine A, B for the corresponding connection, while 1,2 No. of R/TEN then P1 .0, P3.0 access R0, P3.1 then DI. (4), first run on the 2nd machine, type [27]
    2022-02-28 17:08:56下载
    积分:1
  • Brief Introduction to C51 Language
    Brief Introduction to C51 Language
    2022-03-04 19:53:10下载
    积分:1
  • 瑞萨7709系列高档单片机串口通信的工程文件,实现简单的单片机与PC之间的串口通信...
    瑞萨7709系列高档单片机串口通信的工程文件,实现简单的单片机与PC之间的串口通信-Renesas 7709 series high-end single-chip serial communication engineering documents, to achieve a simple and single-chip serial communication between PC
    2023-01-09 01:15:02下载
    积分:1
  • used with a variety of LCD driver chips and sample matrix driver, a very good re...
    含多种常用液晶驱动芯片和点阵驱动程序样例,有很好的参考价值,本人特意会集上传-used with a variety of LCD driver chips and sample matrix driver, a very good reference value, I will deliberately set upload
    2022-08-09 22:41:57下载
    积分:1
  • 696518资源总数
  • 105478会员总数
  • 36今日下载