-
Protel99SE网络表装入常见错误及解决方法
Protel99SE网络表装入常见错误及解决方法
- 2022-03-20 05:03:48下载
- 积分：1
-
这是驱动出租车开票打印机的程序，特殊之处是在留有足够余量的情况下，提高了打印密度让一行打印更多的字符...
这是驱动出租车开票打印机的程序，特殊之处是在留有足够余量的情况下，提高了打印密度让一行打印更多的字符-This is a printer driver taxi invoicing procedures, the special nature of sufficient headroom in the circumstances, improve the print density to allow his characters to print more
- 2022-05-24 11:23:56下载
- 积分：1
-
Nios II study on good information, it is suitable for beginners
一些关于Nios II学习的好资料，很适合初学者-Nios II study on good information, it is suitable for beginners
- 2023-05-14 16:45:03下载
- 积分：1
-
红外遥控逻辑分析器。原代码+电路图
红外遥控逻辑分析器。原代码+电路图 - RAR 压缩文件-Infrared Remote Control logic analyzer. The original code+ Circuit- RAR compressed files
- 2022-03-15 01:14:21下载
- 积分：1
-
STR750开发板的硬件的计时秒表
秒表最大计时时间为3分钟59秒。系统设置2个功能键，控制秒表启停。秒表启动时从00秒开始计数，2位的七段数码管显示变化的秒数（以十进制形式），计数范围为00-59秒。停止键按下，系统维持显示计时的最后值。开发板的2个数码管作为秒表的秒显示，秒表的分钟显示功能由2个LED灯（LD3和LD4）按二进制形式表示，即LD4为最低位，LD3为最高位，当2个全亮时表示3分钟。开发板中的两个按键Key2为开始键，Key3为停止键。
- 2022-07-16 11:46:47下载
- 积分：1
-
TEA5767收音机可以自动搜索上下有代表台湾的…
TEA5767收音机可以自动上下搜台
代有数码管显示等-TEA5767 radio can automatically search up and down there on behalf of the Taiwan digital tube displays
- 2022-06-21 11:10:54下载
- 积分：1
-
MSP430提取信号波形AD转换并串口发送程序
使用仿真器下载到MSP430F149芯片中去后，可以实现对模拟信号的采集，AD转换和串口发送，实测有效
- 2023-05-26 03:15:03下载
- 积分：1
-
文件系统在DSP上的实现，实现了在TIDSP上的文件系统构建，保存
文件系统在DSP上的实现，实现了在TIDSP上的文件系统构建，保存-File system on the DSP implementation, realized in TIDSP file system on the building, preservation
- 2022-05-13 00:21:15下载
- 积分：1
-
zebra测试源代码用于 SOCKET 通信
zebra测试源代码用于 SOCKET 通信-zebratesting code for socket communication
- 2022-02-04 15:58:39下载
- 积分：1
-
Perfect Example for Embedded
Perfect Example for Embedded-C begineers
Explaining use of Data types, Storage class specifiers.
The following code will not immediately run. After being debugged, you are to run this code in the MPLAB environment as outlined in the procedure.
This code, when working, will be a very simple program that initializes two variables, runs a loop, and stops. The variables are Fahrenheit and Celsius representing the two common units of Temperature. The loop walks Fahrenheit through all integers between -212.0 and +212.0 while setting the respective Celsius value each step of the way.-Perfect Example for Embedded-C begineers
Explaining use of Data types, Storage class specifiers.
The following code will not immediately run. After being debugged, you are to run this code in the MPLAB environment as outlined in the procedure.
This code, when working, will be a very simple program that initializes two variables, runs a loop, and stops. The variables are Fahrenheit and Celsius repr
- 2022-03-02 19:58:08下载
- 积分：1
