-
3D场景中的飞机飞行模拟，能进行多视角切换、开火、左右方向。...
3D场景中的飞机飞行模拟，能进行多视角切换、开火、左右方向。-3D scene of the aircraft flight simulation, to carry out multi-angle switching, opened fire on the right and left direction.
- 2022-02-06 05:25:14下载
- 积分：1
-
Edge Sharpening good (image processing)
很好的边缘锐化（图像处理）-Edge Sharpening good (image processing)
- 2022-01-22 03:54:05下载
- 积分：1
-
STM32 Cryptographic Library
STM32 Cryptographic Library
Introduction
This manual describes the API of the STM32 cryptographic library (STM32-CRYP-LIB) that
supports the following cryptographic algorithms:
AES-128, AES-192, AES-256 bits. Supported modes are:
– ECB (Electronic Codebook Mode)
– CBC (Cipher-Block Chaining) with support for ciphertext stealing
– CTR (CounTer Mode)
– CCM (Counter with CBC-MAC)
– GCM (Galois Counter Mode)
– CMAC
– KEY WRAP
ARC4
DES, TripleDES. Supported modes are:
– ECB (Electronic Codebook Mode)
– CBC (Cipher-Block Chaining)
HASH functions with HMAC support:
– MD5
– SHA-1
– SHA-224
– SHA-256
Random engine based on DRBG-AES-128
RSA signature functions with PKCS#1v1.5
ECC (Elliptic Curve Cryptography):
– Key generation
– Scalar multiplication (the base for ECDH)
– ECDSA
These cryptographic algorithms can run in the series STM32F1, STM32 L1, STM32F2,
STM32F4, STM32F0 and STM32F3 with hardware enhancement accelerators.
- 2022-07-21 14:38:08下载
- 积分：1
-
similar brush graphics controls source code
类似画笔的绘图控件源代码-similar brush graphics controls source code
- 2022-08-16 18:12:50下载
- 积分：1
-
看完这个程序后你就知道牛人实在太多，太厉害了！
看完这个程序后你就知道牛人实在太多，太厉害了！-after reading this you will know that so many cattle, too powerful!
- 2022-03-10 01:35:10下载
- 积分：1
-
为了将零件固定在PCB上面，我们将它们的接脚直接焊在布线上。在最基本的PCB（单面板）上，零件都集中在其中一面，导线则都集中在另一面。这么一来我们就需要在板子上...
为了将零件固定在PCB上面，我们将它们的接脚直接焊在布线上。在最基本的PCB（单面板）上，零件都集中在其中一面，导线则都集中在另一面。这么一来我们就需要在板子上打洞，这样接脚才能穿过板子到另一面，所以零件的接脚是焊在另一面上的。因为如此，PCB的正反面分别被称为零件面（Component Side）与焊接面（Solder Side）。-parts to be fixed above the PCB, we will take their feet welded directly on the wiring. At its most basic PCB (single-panel), parts of which are concentrated in the side, wire were concentrated on the other side. Suppose we need burrows on the board, then through the legs of another plank, then parts of the legs is another welding in the face. Because of this, the PCB is negative components were known as surface (Component Side) and the welding surface (Solder Side).
- 2022-11-08 00:30:02下载
- 积分：1
-
图像不变矩的推广，可以利用图像的不变矩进行二次开发
图像不变矩的推广，可以利用图像的不变矩进行二次开发-Image Moment unchanged promotion, we can use the same image for secondary development Moment
- 2022-03-14 04:05:19下载
- 积分：1
-
用VC绘图方面的，可以看看，还不错。对于初中级读者还有些帮助....
用VC绘图方面的，可以看看，还不错。对于初中级读者还有些帮助.-Mapping using VC, you can look pretty good. Junior high school level readers for some help.
- 2022-03-12 12:15:08下载
- 积分：1
-
image processing an entry C source
图像处理入门C源码1-image processing an entry C source
- 2022-01-26 04:53:59下载
- 积分：1
-
国际上开源的矢量化算法，速度堪比R2V软件
国际上开源的矢量化算法，速度堪比R2V软件-international revenue vector algorithm, the speed guaranteed under Application of the R2V software
- 2022-03-24 15:37:28下载
- 积分：1
