-
基于MSP430单片机的封装I2C总线
基于MSP43O单片机的I2C总线软件包-MSP43O based SCM package I2C Bus
- 2023-04-27 12:05:04下载
- 积分：1
-
KEELOQ_DNcode simple to use VB to do the decoding process is very difficult to f...
KEELOQ_DNcode
用VB做的简单的解码程序
很难找到的-KEELOQ_DNcode simple to use VB to do the decoding process is very difficult to find the
- 2022-08-20 07:06:17下载
- 积分：1
-
５１单片机ａｓｍ串口液晶显示器通信程序，已通过测试
５１单片机ａｓｍ串口液晶显示器通信程序，已通过测试-51 SCM asm LCD serial communication program, has passed the test
- 2022-02-12 14:04:00下载
- 积分：1
-
LED大屏幕显示系统的主要程序段 内包含几个主要的函数
LED大屏幕显示系统的主要程序段 内包含几个主要的函数-LED large screen display system
- 2022-01-24 14:46:46下载
- 积分：1
-
用8051单片机做的一个洗菜机的程序，程序用汇编语言写的，以文本方式打开，程序有注释...
用8051单片机做的一个洗菜机的程序，程序用汇编语言写的，以文本方式打开，程序有注释
- 2022-01-30 16:34:47下载
- 积分：1
-
ds2482
ds2482-100是IIC协议转1-wire协议的接口芯片。本程序包利用ds2482-100操作温度传感器ds18s20。注意：ds18s20初始化后温度值为85摄氏度，必须多读几次温度以便其显示稳定。另外，文件中包含的一些头文件可以顾名思义，都是比较通用的（如IIC软件包），为节省篇幅，没有包含进来。请在
编译时自己根据接口函数添加。-ds2482-100 is IIC agreement to 1-wire agreement interface chip. The packages use ds2482-100 ds18s20 operating temperature sensor. Note : After initialization ds18s20 temperature of 85 degrees Celsius, to be read several times the temperature to show its stability. Also, the document contains a number of header files can name suggests, are relatively common (eg IIC package), To save space, are not included come. Please compiled under its own interface function was added.
- 2022-08-23 23:28:31下载
- 积分：1
-
IC Card operating software : AT88SCl604 chip mode of operation there are five. T...
IC卡操作软件:AT88SCl604芯片的操作模式有五种。它们是通过配PGM、RST、CLK等引脚信号及内部地址计数器(IAC)的状态组合来实现。 (1) 芯片复位操作： AT88SCl604有两种复位方式:上电复位和控制复位。 上电复位： 上电复位是当芯片加电时的最初状态。上电复位属于芯片 内部复位。它将使芯片内部所有的隐含标志复位到"0"状态。并使地址计数器复位到0位。 控制复位： 当CLK为低时，在RST脚上的一个下降沿将便芯片产生复位操作。 控制复位是将地址计数器复位到0位，而不影响任何内部标志的状态。-IC Card operating software : AT88SCl604 chip mode of operation there are five. They are allocated by PGM, RST, etc. pin CLK signal and the internal address counter (IAC) portfolio of the state is to be achieved. (1) chip reset operation : reduction AT88SCl604 two ways : power-on reset and reset control. Power-on reset : power-on reset when the chip is in power at the initial state. Power-on reset the internal chip is reset. It will enable all internal chip implied signs reset to "0" state. Make address counter reset to 0. Reset control : When the CLK for the low, the RST feet of a falling edge chips will have to reset operation. Reset control is to address counter reset to 0, without prejudice to any signs of internal sta
- 2022-05-28 08:23:00下载
- 积分：1
-
1―wire总线的详细介绍，对有设计硬件电路的同志有帮助
1―wire总线的详细介绍，对有设计硬件电路的同志有帮助-1-wire bus detailed description of the hardware design of a circuit to help comrades
- 2022-03-18 15:46:35下载
- 积分：1
-
这个范例说明如何使用8051 的Port 1连接LCD显示器，PORT 3.3、P3.4和P3.5则连接到LCD显示器的控制线。程序执行时将显示出Hello K...
这个范例说明如何使用8051 的Port 1连接LCD显示器，PORT 3.3、P3.4和P3.5则连接到LCD显示器的控制线。程序执行时将显示出Hello Keil C和LCD display */-This example shows how to use the 8051 Port 1 to connect LCD displays, PORT 3.3, P3.4 and P3.5 are connected to the LCD display control lines. Program execution will show Hello Keil C, and LCD display* /
- 2022-01-20 22:46:27下载
- 积分：1
-
PS2 keyboard and 1602 LCD programming, hope you instruct
PS2键盘和1602液晶显示器件的编程，望高手指点-PS2 keyboard and 1602 LCD programming, hope you instruct
- 2022-04-29 04:24:37下载
- 积分：1
