登录
首页 » 嵌入式芯片 » 44B0的测试程序代码,此程序介绍了44B0 的IIC的应用方法并给出了完整原程序...

44B0的测试程序代码,此程序介绍了44B0 的IIC的应用方法并给出了完整原程序...

于 2022-01-26 发布 文件大小:34.41 kB
0 213
下载积分: 2 下载次数: 1

代码说明:

44B0的测试程序代码,此程序介绍了44B0 的IIC的应用方法并给出了完整原程序-44B0 test code, this procedure 44B0 of the IIC and the application is a complete original program

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • arm9200t上的一个叫busybox的东西,,,最近用不上,拿来大家用吧,,,供参考...
    arm9200t上的一个叫busybox的东西,,,最近用不上,拿来大家用吧,,,供参考-arm9200t a thing called busybox, recently do not have access to, use it with everyone,,, for reference
    2022-03-20 01:41:42下载
    积分:1
  • 周立功MiniARM
    ZLG MINIARM-N20系列最新的底层驱动的使用说明!-ZLG MINIARM-N20 series of up-to-date bottom-driven use!
    2022-08-11 01:26:38下载
    积分:1
  • err
    LPC2200系列的RAM测试程序,已改进,当RAM有故障会,急声报警;正常这按心跳频率发声。 改地址也可以用来有效测试FLASH-err
    2022-07-26 13:17:16下载
    积分:1
  • 彩色OLED,stm32f10x
    彩色OLED,stm32f10x. 实现画点,画圆形.暂无字库.lcd led oled液晶显示驱动程序
    2022-02-03 10:22:53下载
    积分:1
  • S3C44B0x中RTC的使用方法 寄存器的使用很有借鉴意义
    S3C44B0x中RTC的使用方法 寄存器的使用很有借鉴意义 -S3C44B0X in the RTC registers to use the use of referential significance to
    2022-09-05 16:55:03下载
    积分:1
  • s3c4510 bsd
    s3c4510 bsd
    2022-01-26 04:07:34下载
    积分:1
  • 代码用简单的4个IO口外加两个ADC转换接口实现了触摸屏全套控制流程....
    代码用简单的4个IO口外加两个ADC转换接口实现了触摸屏全套控制流程.-Code with a simple four IO port plus two ADC conversion of the touch screen interface to achieve a full set of control flow.
    2022-01-25 15:50:33下载
    积分:1
  • ARM7TDMI的修订:r4p1技术参考手册。
    ARM7TDMI Revision: r4p1 Technical Reference Manual.
    2022-01-21 01:22:33下载
    积分:1
  • 常用ARM指令集及汇编
    常用ARM指令集及汇编-commonly used ARM instruction set and compilation
    2022-03-19 04:39:20下载
    积分:1
  • his project was built and tested with WinAVR
    his project was built and tested with WinAVR-20060125. Make sure the MCU target define in the Makefiles corresponds to the AVR you are using!! To build the code, just install WinAVR and run "make" from the console in echomaster and echoslave subdirs. "make program" will program the device if you have a AVRISP attached. Remember to set the AVR device to at least 8MHz. The AVR may use the programmable clock from MC1319x, just remember to check if the MC1319x and SPI communication is working FIRST! Otherwise you wont get any clock signal to the AVR and then you can t program it or reset the fuses! The MC1319x has default clock output of 32kHz so you will have to set your programmer to a very low frequency (
    2023-02-22 21:55:03下载
    积分:1
  • 696516资源总数
  • 106908会员总数
  • 1今日下载