登录
首页 » 汇编语言 » 分形

分形

于 2022-02-03 发布 文件大小:925.00 B
0 171
下载积分: 2 下载次数: 1

代码说明:

分形--- ----羊齿叶 不错的-reaching back to the good leaf

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • S1实验板 AT89C51 12M晶振 乘法实验0FFH*03H=02FDH=756在P0口和P1口显示...
    S1实验板 AT89C51 12M晶振 乘法实验0FFH*03H=02FDH=756在P0口和P1口显示 -S1 board multiplication experiment AT89C51 12M crystal 0FFH* 03H = 02FDH = 756 in the P0 and P1 mouth I show
    2022-05-06 12:33:44下载
    积分:1
  • 电动门程序急图纸
    电动门程序急图纸-electric doors dire drawings
    2022-05-18 06:26:18下载
    积分:1
  • 一个模拟时钟的程序
    一个模拟时钟的汇编语言程序-an analog clock Assembly Language Program
    2023-01-27 08:50:04下载
    积分:1
  • 此程序是关系电子时钟的,用写成,功能比较完哟
    此程序是关系电子时钟的,用汇编写成,功能比较完哟-this program is the electronic clock with a compilation languages, a more complete functional yo
    2023-06-18 22:05:03下载
    积分:1
  • 100
    100点温度值采集,并且可以进行摄氏温度和华氏温度的转换-100-point temperature value acquisition, and can be carried out Celsius and Fahrenheit temperature conversion
    2022-04-14 22:08:07下载
    积分:1
  • 内部有说明,多为嵌入式系统程序,侧重于实用的系统,很有参考价值...
    内部有说明,多为嵌入式系统程序,侧重于实用的系统,很有参考价值-internal notes, and many of the embedded system, with a focus on practical, useful reference value
    2023-04-07 05:25:03下载
    积分:1
  • asp网上购物系统 论文ASPeshplunwenyuanma
    asp网上购物系统 论文ASPeshplunwenyuanma-ASPeshplunwenyuanma
    2022-03-24 03:53:08下载
    积分:1
  • 模糊控制方法来控制无刷直流电动机调速,电机转速可以显著…
    采用模糊控制方式控制直流无刷电机的转速,可使电机的转速稳定性大幅度提高-Fuzzy control method to control brushless DC motor speed, motor speed can significantly improve the stability of
    2022-02-09 15:53:06下载
    积分:1
  • 操作蜂鸣器演奏音乐的例程,使用MASM6.15译通过
    汇编操作蜂鸣器演奏音乐的例程,使用MASM6.15编译通过-operation of buzzer
    2022-02-15 05:23:26下载
    积分:1
  • way light
    是一个汇编延时程序,适合初学者使用,当P1.0端口输出高电平,即P1.0=1时,根据发光二极管的单向导电性可知,这时发光二极管L1熄灭;当P1.0端口输出低电平,即P1.0=0时,发光二极管L1亮;我们可以使用SETB P1.0指令使P1.0端口输出高电平,使用CLR P1.0指令使P1.0端口输出低电平。 -Delay is a compilation of procedures, suitable for beginners to use, when the high output port P1.0, P1.0 = 1 that is, when the one-way light-emitting diodes based on conductivity, we can see that this light-emitting diodes L1 extinguished when P1. 0 port output low, that is, P1.0 = 0, the light-emitting diodes L1-liang we can use the command SETB P1.0 port P1.0 output high to enable the use of instructions to enable CLR P1.0 output port P1.0 low.
    2022-05-20 21:18:00下载
    积分:1
  • 696518资源总数
  • 106235会员总数
  • 12今日下载