-
ZLG LPC2114
ZLG LPC2114基楚上开发的一个电池监测板源程序，这里主要的IC是DS2764（锂电池监控IC）。
文件：
Ds2764.mcp
Ds2764.HEX
LPC2294.H
等相关文件。-ZLG LPC2114-based Chu developed a battery monitoring board source, where the main IC is DS2764 (Li-ion battery monitor IC). File: Ds2764.mcpDs2764.HEXLPC2294.H and other relevant documents.
- 2022-07-09 11:33:55下载
- 积分：1
-
Two
双向传输协议，如自动检测I2C传输协议COM端口需要连接
- 2022-04-10 21:03:34下载
- 积分：1
-
atmel公司推出的eeprom资料，128k/256k.
atmel公司推出的eeprom资料，128k/256k.-ATMEL company"s EEPROM, 128k/256k.
- 2022-09-11 23:30:03下载
- 积分：1
-
2802步进电机控制器，可以作为步进电机驱动的一个重要的…
2802 步进电机控制器，可以作为步进电机驱动设计的重要参考-2802 stepper motor controller, stepper motor driver can be used as an important reference design
- 2022-07-15 13:46:34下载
- 积分：1
-
自动汽车安全带
我的目标是项目的要使它明确所以过坐在车里必须穿带虽然车启动.so 我要一个新的方式在其中很想去那设计汽车座椅带系统使我们不忘锁安全带的设计。所以我在此系统中使的人坐在那辆车自动获取与安全带锁着这种电机械系统。
- 2022-07-04 13:05:42下载
- 积分：1
-
8051 works in 11.0592MHZ, RAM expansion for the 128KB of 628128, FlashRom extend...
8051工作于11.0592MHZ,RAM扩展为128KB的628128,FlashRom扩展为128KB的AT29C010A
128KB的RAM分成4个区(Bank) 地址分配为0x0000-0x7FFF
128KB的FlashRom分成8个区(Bank) 地址分配为0x8000-0xBFFF
为了使8051能访问整个128KB的RAM空间和128KB的FlashRom空间,在CPLD内建两个寄存器
RamBankReg和FlashRomBankReg用于存放高位地址-8051 works in 11.0592MHZ, RAM expansion for the 128KB of 628128, FlashRom extended AT29C010A 128KB to 128KB of the RAM is divided into four zones (Bank) Address Assignment for the 0x0000-0x7FFF 128KB FlashROM divided into eight zones (Bank) Address Assignment for the 0x8000- 0xBFFF in order to enable the 8051 to access the entire 128KB and 128KB of RAM space of FlashROM space, two built-in CPLD register RamBankReg and used to store high FlashRomBankReg Address
- 2022-05-30 14:55:40下载
- 积分：1
-
嵌入式系统Ateml板
embedded system about Ateml board
- 2022-09-25 17:45:03下载
- 积分：1
-
T-Kernel 嵌入式系统源码，非常好用！-T-Kernel source embedded system is very easy to use!
- 2022-12-28 16:25:04下载
- 积分：1
-
另一个湿度传感器采集源码，可以在单片机上使用。
另一个湿度传感器采集源码，可以在单片机上使用。-Another humidity sensor capture source, you can use the microcontroller.
- 2022-02-14 08:12:47下载
- 积分：1
-
3D打印机 marlin
应用背景The leading developers of Marlin are currently (January 2015) EvdZ and bkubicek, though many others contribute with their patches. This is a firmware for reprap single-processor electronics setups. It also works on the Ultimaker PCB. It supports printing from SD card+Folders, and look-ahead trajectory planning. This work is licensed under the GNU GPL v3 or (at the user"s discretion) any later version. It is based on Sprinter firmware, which was licensed under GPL v2 or later.关键技术
Features:
Interrupt based movement with real linear acceleration.
High steprate.
Look ahead (Keep the speed high when possible. High cornering speed).
Interrupt based temperature protection.
preliminary sup
- 2022-03-06 02:29:58下载
- 积分：1
