-
基于C51单片机的多机串口,MODBUS协议通讯的实现方法.
基于C51单片机的多机串口,MODBUS协议通讯的实现方法.-C51 Microcontroller Based Multi-machine serial port, MODBUS communication protocol implementations.
- 2023-09-02 16:55:03下载
- 积分：1
-
mathacad laboratore usings sdk
mathacad laboratore usings sdk
- 2022-01-24 12:46:25下载
- 积分：1
-
1602液晶屏的使用说明手册，很实用哦，对于使用VHDL编写液晶屏驱动具有参考价值。...
1602液晶屏的使用说明手册，很实用哦，对于使用VHDL编写液晶屏驱动具有参考价值。-1602 LCD screen use the instruction manual, it is practical Oh, for the use of VHDL LCD driver with the preparation of reference value.
- 2022-03-07 13:58:51下载
- 积分：1
-
由单片机控制的蜂鸣器，唱出猪之歌的音乐，用C语言编的程序。...
由单片机控制的蜂鸣器，唱出猪之歌的音乐，用C语言编的程序。-SCM control buzzer singing Song of Pig C-language program
- 2022-02-11 17:56:31下载
- 积分：1
-
单片机脉搏测量仪的电路设计和源码，包括KEIL调试文件和PROTEUS仿真文件...
单片机脉搏测量仪的电路设计和源码，包括KEIL调试文件和PROTEUS仿真文件-Single-chip pulse measuring instrument circuit design and source code, including KEIL debug files and documents PROTEUS simulation
- 2022-02-11 23:39:04下载
- 积分：1
-
一种实现载波监听多点接入／冲突检测的多主RS485总线
一种实现载波监听多点接入／冲突检测的多主RS485总线-A carrier sense realize multi-point access/Collision Detection RS485 multi-master bus
- 2022-02-27 06:27:24下载
- 积分：1
-
红外线遥控解码器,该程序实现将红外遥控器发出的红外线解码，并通过LCD显示出来...
红外线遥控解码器,该程序实现将红外遥控器发出的红外线解码，并通过LCD显示出来 -infrared remote control decoder, the program will infrared remote control and using the infrared decoding, and out through the LCD display
- 2022-12-27 20:15:04下载
- 积分：1
-
keilc+ proteus light parallel port design of experiments requirements: master th...
keilc + proteus
并行口设计指示灯实验
要求：掌握80C51单片机输入输出接口使用方法
学会开关量输入输出控制的接口技术及编程方法
实验题目：8个发光二极管D1~D8分别接在单片机P1.0-P1.7端口上，一个开关接在P3.0上。要求输出端口输出 “0”时，发光二极管亮。开关闭合时，开始按P1.0-P1.1-...-P1.7的顺序依次点亮LED，再按 P1.7-P1.6 -...-P1.0的顺序点亮LED，重复循环。开关断开时，立刻停止点亮指示灯。-keilc+ proteus light parallel port design of experiments requirements: master the 80C51 microcontroller input and output interfaces Society of switch to use the amount of input and output control interface technology and programming methods Experimental subjects: eight light-emitting diodes D1 ~ D8, respectively connected to the MCU P1.0-P1 .7 port on a switch connected to the P3.0 on. Requested output port output " 0" , the light-emitting diode light. Is closed, to embark on the P1.0-P1.1-...- P1.7 in the order light LED, and then P1.7-P1.6-...- P1.0 order light LED Repeat cycle. Switch off when the stop light indicator.
- 2022-11-16 18:10:03下载
- 积分：1
-
MSP430和nRF24L01
msp430与NRF24L01通信例程 相对很完整-msp430 and nrf24L01
- 2022-04-18 11:10:41下载
- 积分：1
-
8051智能化家电控制源代码
8051智能化家电控制源代码-8051 intelligent appliance control source code
- 2023-05-28 23:45:03下载
- 积分：1
