-
独立数码管计数，从0到99的计数，然后再清零。比较简单的代码。...
独立数码管计数，从0到99的计数，然后再清零。比较简单的代码。-Independent digital control counts, 0-99 from the count, and then cleared. The code is relatively simple.
- 2022-02-05 07:13:10下载
- 积分：1
-
NBA 24 seconds timer design
NBA24秒计时器设计，用单片机设计成功的，包括最终的报告-NBA 24 seconds timer design
- 2022-08-03 22:13:15下载
- 积分：1
-
Difficult to get the best original source rtd3523 Series LCD driver development,...
很难得的最好的rtd3523系列原厂源码LCD驱动开发，及相关的显示系统开发！-Difficult to get the best original source rtd3523 Series LCD driver development, and related display systems development!
- 2022-01-26 01:56:41下载
- 积分：1
-
这是一个对单片机IO口，进行操作的程序，有助于对单片机硬件的了解...
这是一个对单片机IO口，进行操作的程序，有助于对单片机硬件的了解-failed to translate
- 2022-05-06 01:48:22下载
- 积分：1
-
pic18f2480的can模块初始化函数以及基本的收发操作
pic18f2480的can模块初始化函数以及基本的收发操作-can the pic18f2480 module initialization function, as well as send and receive basic operation
- 2022-08-14 20:55:08下载
- 积分：1
-
红外遥控接收
ORG 0000H
LJMP START 转入主程序
ORG 0010H
START:
MAIN:
JNB P2...
红外遥控接收
ORG 0000H
LJMP START 转入主程序
ORG 0010H
START:
MAIN:
JNB P2.2,IR
LJMP MAIN
以下为进入P3.2脚外部中断子程序，也就是解码程序
IR:
MOV R6,#9
SB:
ACALL DELAY882 调用882微秒延时子程序
JB P2.2,EXIT 延时882微秒后判断P3.2脚是否出现高电平如果有就退出解码程序
DJNZ R6, SB 重复10次，目的是检测在8820微秒内如果出现高电-infrared remote control receiver ORG 0000H LJMP START into main program ORG 0010H START : MAIN : JNB P2.2, IR LJMP MAIN below to enter P3.2 foot external interrupt subroutine, which is decoding procedures IR : MOV R6, SB# 9 : Calling ACALL DELAY882 882 microsecond delay subroutine JB P2.2, EXIT 882 microsecond delay after the judgment whether there P3.2 feet to I quit if decoding procedures DJNZ R6, SB repeated 10 times, the purpose is to test if within 8,820 microsecond high
- 2022-07-21 10:12:11下载
- 积分：1
-
LCD display code, and driver chips for the s6b0741, with the Spanish show, Chine...
LCD显示代码，驱动芯片为s6b0741，带有西文显示，中文显示，图片显示，数字显示等功能-LCD display code, and driver chips for the s6b0741, with the Spanish show, Chinese display, picture display, digital display and other functions
- 2023-01-09 16:15:04下载
- 积分：1
-
基于51单片机的温度和电压采集与循环显示的控制程序，其中温度传感器为LMA95，采用I2C总线传输，显示器为8段LED数码管...
基于51单片机的温度和电压采集与循环显示的控制程序，其中温度传感器为LMA95，采用I2C总线传输，显示器为8段LED数码管-51 single-chip-based temperature and voltage of the cycle of acquisition and display of the control procedures, including temperature sensors for LMA95, using I2C bus transmission, display for the 8 LED digital tube
- 2022-01-24 14:42:39下载
- 积分：1
-
DDS special chip in the microcontroller and control, and then display
在单片机和DDS专用芯片进行控制，再显示-DDS special chip in the microcontroller and control, and then display
- 2022-04-11 19:11:59下载
- 积分：1
-
msp430f149键盘中断程序，用端口中断。通过实验验证
msp430f149键盘中断程序，用端口中断。通过实验验证-msp430f149 keyboard interrupt procedures, using ports interruption. Experimental verification
- 2022-07-22 11:30:24下载
- 积分：1
