-
本程序是i2c总线读写一个字节的程序。在写过程序中，不一定非要检测i2c的应答位，可以直接延时过去就行，但是在读过程中必须给应答信号，读完发停止位，一定确认所发...
本程序是i2c总线读写一个字节的程序。在写过程序中，不一定非要检测i2c的应答位，可以直接延时过去就行，但是在读过程中必须给应答信号，读完发停止位，一定确认所发的信号都发上了。否则在连续地址读的过程中可能不会出错，但是在随机度过程中就会出错，我的程序就是在给停止信号时没有给上，24cxx一直在输出数据，结果读出错。找着问题后我的程序只加入了一条命令便完全正常。-i2c bus read and write a byte procedures. The written procedure, not necessarily require the detection i2c-response, and can directly past trip delay, but the process must be read to the response signal, stopped at reading, we recognize the signals are on the fat. Otherwise, the address read for the course could not go wrong, but the randomness of the process would be a mistake, I was in the process to stop for no signal, 24cxx in output data, read errors. I discovered the problem after the procedure just joined the order of a completely normal.
- 2022-02-02 10:09:18下载
- 积分：1
-
SZ328串行通讯驱动及应用开发包,为2个CPU间协议通讯应用实例.
SZ328串行通讯驱动及应用开发包,为2个CPU间协议通讯应用实例.-SZ328 serial communication driver and application development kit for the two inter-CPU communication protocol application.
- 2022-10-04 15:25:03下载
- 积分：1
-
Look uptable for temprature system. To check kp, Ki of system
Look uptable for temprature system. To check kp, Ki of system
- 2022-03-25 06:15:26下载
- 积分：1
-
W77E58 dual serial communication source code Note : This program is for referenc...
W77E58双串口通信源代码
注：此源程序只作参考，内有些函数未有原型，借鉴在于其通信方式及其设置。
CRC检校可另参考其它代码。
-W77E58 dual serial communication source code Note : This program is for reference only, not some function prototype experiences in his means of communication and set up. CRC calibration can be a reference to other codes.
- 2022-02-16 06:53:32下载
- 积分：1
-
SPI串行总线的AT45DB081的C语言控制源程序
SPI串行总线的AT45DB081的C语言控制源程序-the c progranm code of AT45DB081 with SPI serial bus
- 2022-02-10 14:11:04下载
- 积分：1
-
我个人收集的C++builder 多线程串口通信方面的
我个人收集的C++builder 多线程串口通信方面的-my personal collection of multi-threaded C builder of serial communication Wanton
- 2022-08-22 06:20:02下载
- 积分：1
-
Bluetooth
Bluetooth
- 2022-03-05 11:22:11下载
- 积分：1
-
8583芯片编程应用写入器件地址写8574端口，写入器件地址读8574端口。...
8583芯片编程应用写入器件地址写8574端口，写入器件地址读8574端口。-8583 Application Programming chip device addresses written into the 8574 port, write device address read 8,574 ports.
- 2022-01-31 14:54:29下载
- 积分：1
-
CAN program for PIC microprocessor
CAN program for PIC microprocessor
- 2022-04-27 01:14:50下载
- 积分：1
-
串口通信与工程实践tty编程TTY.dsp,TTY.h
串口通信与工程实践tty编程TTY.dsp,TTY.h-Serial Communication tty programming and engineering practice TTY.dsp, TTY.h
- 2022-06-21 01:23:20下载
- 积分：1
