登录
首页 » Matlab » 倒立摆的滑模控制

倒立摆的滑模控制

于 2022-02-14 发布 文件大小:187.73 kB
0 121
下载积分: 2 下载次数: 4

代码说明:

本文是对“非线性系统的模型参考滑模控制”方法的再仿真

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • analysis
    : 正交频分复用( O F D M) 是第四代移动通信的核心技术。 该文首先简要介绍了O F D M基本原理, 重点研究了理想同步情 况下, 保护时隙( c P )和不同的信道估计方法在高斯信道和多径瑞利衰落信道下对O F D M系统性能的影响。 在给出O F DM系 统模型的基础上, 用 MAT L A B语言实现了整个系统的计算机仿真并给出参考设计程序。 最后给出在不同的信道条件下, 保 护时隙、 信道估计方法对 OF DM系统误码率影响的比较曲线, 得出了较理想的结论。 关键词: 正交频分复用; 仿真; 循环前缀; 信道估计(good)
    2010-06-03 19:23:27下载
    积分:1
  • antenna
    说明:  环天线、单极子天线、口径天线、圆环阵列天线、喇叭天线的远场方向图绘制(Far-field pattern drawing of ring antenna, monopole antenna, aperture antenna, ring array antenna and horn antenna)
    2020-06-23 05:20:02下载
    积分:1
  • clutter-simulation
    包含四种常见分布的杂波仿真程序。均采用相干相关模拟的方法,方法见word文档。(Distribution contains four common clutter simulation program. Are related to the coherent simulation method, the method see the word document.)
    2011-02-11 20:35:31下载
    积分:1
  • MATLAB-optimization
    《精通MATLAB最优化计算》一书中各章实例的源代码程序(" Mastering MATLAB optimization calculations," a book chapter example source code of the program)
    2011-10-17 19:55:35下载
    积分:1
  • PROPOSED-CODE
    Image enhancement using dwt
    2012-04-13 15:48:29下载
    积分:1
  • tingfou
    cordic算法的matlab仿真,采用累计贡献率的方法,小波包分析提取振动信号中的特征频率。( cordic matlab simulation algorithm, The method of cumulative contribution rate Wavelet packet analysis to extract vibration signal characteristic frequency.)
    2016-12-29 01:04:15下载
    积分:1
  • 根据地层参数(速度、密度、厚度),设计相应子波,合成地震记录hecheng
    说明:  根据地层参数(速度、密度、厚度),设计相应子波,合成地震记录(According to the formation parameters (velocity, density, thickness), the corresponding wavelet is designed to synthesize the seismic record)
    2019-12-07 15:00:31下载
    积分:1
  • BinaryParticleswarmoptimization
    binary pso algorithm
    2010-07-08 21:54:50下载
    积分:1
  • attachments
    header file foe edf file
    2010-11-02 03:09:21下载
    积分:1
  • RBFNN
    Three function for RBF neural network, using OLS,Rand and SGA function [newcenter,sigma,W,yh,rmse]=rbfols(p,t,tol) p 為輸入資料點,N×K矩陣,N是輸入資料維度,K是資料點數 t 為目標輸出值,1×K矩陣 tol 為指定容忍度或正確率 centers選定中心點,N×nc矩陣 sigma為 ? 值 W為輸出層權重,nc×1矩陣 yh為網路輸出值,1×K矩陣 rmse 為目標輸出值與網路輸出值之RMSE
    2009-12-10 10:25:35下载
    积分:1
  • 696518资源总数
  • 106259会员总数
  • 28今日下载