登录
首页 » SCM » 液晶显示器LCD1602的驱动。适合于51单片机系统。

液晶显示器LCD1602的驱动。适合于51单片机系统。

于 2022-02-20 发布 文件大小:21.16 kB
0 168
下载积分: 2 下载次数: 1

代码说明:

液晶显示器LCD1602的驱动。适合于51单片机系统。-LCD1602 LCD driver. Suitable for single-chip microcomputer system 51.

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • 基于AD89S52的驱动12864液晶的源程序。
    基于AD89S52的驱动12864液晶的源程序。-On AD89S52 LCD source driver 12864.
    2022-04-07 00:24:02下载
    积分:1
  • 一种实用的12864 液晶驱动程序,已经有实物验证
    一种实用的12864 液晶驱动程序,已经有实物验证 -12864 A practical liquid crystal driver, has been kind to verify
    2023-08-18 12:00:03下载
    积分:1
  • At can be given its arguments in a file. You can comment out lines by precedin...
    At can be given its arguments in a file. You can comment out lines by preceding them with either # or - characters. This is an easy way to temporarily disable some commands. The CONTINUE-command is most useful at the end of the file. When this command is read, the file is started again from the beginning. You can use it situations where the machine is not shut down for the night and you want to run some commands every day.- At can be given its arguments in a file. You can comment out lines by preceding them with either# or- characters. This is an easy way to temporarily disable some commands. The CONTINUE-command is most useful at the end of the file. When this command is read, the file is started again from the beginning. You can use it situations where the machine is not shut down for the night and you want to run some commands every day.
    2022-02-21 09:29:04下载
    积分:1
  • This document is a thesis, complete hardware and software, took a month to compl...
    该文档是一篇毕业论文,硬件和软件齐全,历时一个月完成,非常不错-This document is a thesis, complete hardware and software, took a month to complete, very good
    2023-03-16 22:55:03下载
    积分:1
  • TTR056 MCU control code! Taiwan Winton SCM Interface Converter application code!
    TTR056单片机控制代码!台湾通泰单片机接口转换应用代码!-TTR056 MCU control code! Taiwan Winton SCM Interface Converter application code!
    2022-06-16 17:24:52下载
    积分:1
  • 由MSP430 控制实现的 短消息收发功能的系统 可利用单片机的 串口与无线MODEM 进行连接在进行发送和解析数据 必须按照PDU的格式进行处理...
    由MSP430 控制实现的 短消息收发功能的系统 可利用单片机的 串口与无线MODEM 进行连接在进行发送和解析数据 必须按照PDU的格式进行处理-MSP430 control achieved by the Short Message System transceiver functions of the MCU can be used with wireless modem serial port to connect to send and conducting analytical data must be in accordance with the format PDU processing
    2022-10-29 14:15:03下载
    积分:1
  • [日期:2005
    [日期:2005-11-29] 来源:侃单片机 作者:etiller [字体:大 中 小] -[Date :2005-11-29] Sources: McCain Singlechip Author: etiller [Font: Xinhuanet]
    2022-05-27 09:24:17下载
    积分:1
  • keilc+ proteus light parallel port design of experiments requirements: master th...
    keilc + proteus 并行口设计指示灯实验 要求:掌握80C51单片机输入输出接口使用方法 学会开关量输入输出控制的接口技术及编程方法 实验题目:8个发光二极管D1~D8分别接在单片机P1.0-P1.7端口上,一个开关接在P3.0上。要求输出端口输出 “0”时,发光二极管亮。开关闭合时,开始按P1.0-P1.1-...-P1.7的顺序依次点亮LED,再按 P1.7-P1.6 -...-P1.0的顺序点亮LED,重复循环。开关断开时,立刻停止点亮指示灯。-keilc+ proteus light parallel port design of experiments requirements: master the 80C51 microcontroller input and output interfaces Society of switch to use the amount of input and output control interface technology and programming methods Experimental subjects: eight light-emitting diodes D1 ~ D8, respectively connected to the MCU P1.0-P1 .7 port on a switch connected to the P3.0 on. Requested output port output " 0" , the light-emitting diode light. Is closed, to embark on the P1.0-P1.1-...- P1.7 in the order light LED, and then P1.7-P1.6-...- P1.0 order light LED Repeat cycle. Switch off when the stop light indicator.
    2022-11-16 18:10:03下载
    积分:1
  • verilig准备使用CPLD读写EEPROM(74lc21)程序
    利用Verilig编写CPLD读写EEPROM(74LC21)程序-Verilig prepared to use CPLD to read and write EEPROM (74LC21) procedures
    2023-04-03 15:35:03下载
    积分:1
  • C51 man
    C51人机接口技术,有4×4键盘程序显示及其仿真-C51 man-machine interface technology, there are 4 × 4 keyboard display and simulation
    2022-06-13 06:47:38下载
    积分:1
  • 696518资源总数
  • 106253会员总数
  • 14今日下载