登录
首页 » USB develop » jlink4编程ARM微控制器的USB接口和JTAG编程和设计。

jlink4编程ARM微控制器的USB接口和JTAG编程和设计。

于 2022-03-05 发布 文件大小:132.73 kB
0 162
下载积分: 2 下载次数: 1

代码说明:

jlink4 programming arm microcontroller usb interface and jtag programming and debugging

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • usb2.0协议,用于usb开发的参考资料
    usb2.0协议,用于usb开发的参考资料-USB 2.0 protocol for the development of reference materials usb
    2022-08-06 22:21:10下载
    积分:1
  • TUSB3210固件开发源程序(C语言、开发环境keil)
    TUSB3210固件开发源程序(C语言、开发环境keil)-TUSB3210 source firmware development (C language development environment keil)
    2022-12-13 13:10:03下载
    积分:1
  • EZUSB 驱动,自己编写的,需要的可以
    EZUSB 驱动,自己编写的,需要的可以-EZUSB drive, I have written, take a look at the necessary
    2022-04-06 15:44:20下载
    积分:1
  • 本程序演示了如何利用编写高层应用程序与USB接口通信
    本程序演示了如何利用编写高层应用程序与USB接口通信-this program demonstrated how to use the preparation of high-level applications and USB communications
    2022-03-10 05:22:49下载
    积分:1
  • 这个一个usb接口芯片ch372的,上位机(PC)机程序,用vc编写。...
    这个一个usb接口芯片ch372的,上位机(PC)机程序,用vc编写。-this one usb interface chip ch372, PC (PC) Program, prepared using vc.
    2022-09-30 11:20:03下载
    积分:1
  • The programming of application of the USB interface
    USB接口应用编程-The programming of application of the USB interface
    2022-07-25 23:02:27下载
    积分:1
  • USB2.0 specification English
    USB2.0的技术规范 英文-USB2.0 specification English
    2022-03-14 12:51:01下载
    积分:1
  • USB Host 开发中支持数码相机的源码。即Picture To Picture协议的完整实现...
    USB Host 开发中支持数码相机的源码。即Picture To Picture协议的完整实现-Source code for USB Host development supporting digital camera. Full implement of Picture To Picture Protocol.
    2022-07-09 19:36:15下载
    积分:1
  • USB设备
    USB设备端固件程序,枚举部分是全部程序的基础和重心,只有主机对设备枚举成功后,主机才能和设备进行正常的通信 USB的枚举过程分为4个状态. 1.接入态 v主机检测到USB设备插上,击活端口,并发送复位命令(保持10ms) 2.默认态 v主机使用默认地址读取设备描述符 (GET_DESCRIPTOR) v主机分配给设备一个总在线的唯一地址 (SET_ADDRESS) 3.地址态 v主机从新的地址获取设备描述符(GET_DESCRIPTOR) v主机获取所有设备的配置描述符(GET_DESCRIPTOR) 4.配置态 v主机设置描述符(设备,配置) (SET_CONFIGURATION) v主机读取配置状态(可选) (GET_CONFIGURATION) v主机读取接口状态(可选) (GET_INTERFACE) -USB device-side firmware, enumerate all part of the foundation and focus of the procedure, only the host of equipment after the successful enumeration, the host and equipment in order to engage in normal communication USB enumeration process is divided into four status. 1. Access state v host detected USB devices plug in, hit live ports, and send the reset command (to maintain 10ms) 2. default state v Use the default address of the host to read device descriptor (GET_DESCRIPTOR) v host assigned to the equipment of a total online only Address (SET_ADDRESS) 3. A
    2022-01-21 17:52:38下载
    积分:1
  • ADC和SRAM存储采集点DMA。通过改变采样时间…
    acquisition with ADC and storing in SRAM wuth DMA. change sampling time throught USB and transfer sampling throught usb protocol in terrupt.
    2022-02-19 21:45:04下载
    积分:1
  • 696518资源总数
  • 106161会员总数
  • 5今日下载