-
DS1302时钟:综合应用定时器中断溢出,串口通信
实验现象: 每隔4SPC机得一时间,十六进制格式...
DS1302时钟:综合应用定时器中断溢出,串口通信
实验现象: 每隔4SPC机得一时间,十六进制格式-DS1302 Clock: integrated application timer overflow interrupts, serial communication experimental phenomenon: every 4SPC machine was a time, in hexadecimal format
- 2023-05-17 15:30:02下载
- 积分：1
-
ATMEGA128的ADC驱动程序，对自己编写端口驱动的同志有很大的帮助！...
ATMEGA128的ADC驱动程序，对自己编写端口驱动的同志有很大的帮助！-ATMEGA128 the ADC driver, port driver of their comrades in the preparation of great help!
- 2022-04-29 18:07:39下载
- 积分：1
-
单片机游戏程序，包括经典‘俄罗斯方块’等。
单片机游戏程序，包括经典‘俄罗斯方块’等。-SCM games, including the classic " Tetris" and so on.
- 2022-03-26 14:31:16下载
- 积分：1
-
32位arm9微处理器S3C2410的中断程序测试源代码
32位arm9微处理器S3C2410的中断程序测试源代码-32-bit ARM9 microprocessor S3C2410 interruption procedures to test the source code
- 2022-01-26 01:30:53下载
- 积分：1
-
本实验实现PS/2接口与RS
本实验实现PS/2接口与RS-232接口的数据传输，
PS/2键盘上按下按键，可以通过RS-232自动传送到主机的串口调试终端上（sscom32.exe）；
并在数据接收区显示接收到的字符。
串口调试终端的设置：波特率115200，一个停止位，无校验位。
-Realize this experiment, PS/2 interface with RS-232 data interface, PS/2 keyboard to press the button, through RS-232 automatic transmission to the host serial debug terminal (sscom32.exe) and data receiving display received characters. Serial debug terminal settings: 115200 baud rate, one stop bit, no parity bit.
- 2022-10-12 11:00:03下载
- 积分：1
-
用ATmega8实现累加功能，并用数码管实现显示。
用ATmega8实现累加功能，并用数码管实现显示。-Cumulative function with ATmega8 realize, and realize digital tube display.
- 2023-08-19 07:15:03下载
- 积分：1
-
x5054 read and write procedures. With 80S51 control. C language, helps the reade...
x5054读写程序。用80S51控制。C语言，有助于了解存储器的读写-x5054 read and write procedures. With 80S51 control. C language, helps the reader to understand memory
- 2022-07-11 13:51:44下载
- 积分：1
-
cf8020+cp2200(网络)的驱动实现
cf8020+cp2200(网络)的驱动实现-cf8020+ cp2200 (network) drivers realize
- 2022-10-26 22:10:03下载
- 积分：1
-
飞思卡尔S12 系列单片机系统硬件设计，详细介绍了该单片机的硬件使用，为全中文，MC9S12DG128B 有16路AD 转换，精度最高可设置为10 位；有8 路...
飞思卡尔S12 系列单片机系统硬件设计，详细介绍了该单片机的硬件使用，为全中文，MC9S12DG128B 有16路AD 转换，精度最高可设置为10 位；有8 路8 位PWM 并可两两级联为16 位精度PWM，特别适合用于控制多电机系统。它的串行通信端口也非常丰富，有2 路SCI，2 路SPI 此外还有IIC，CAN总线等端口，并且采用了引角复用功能，使得这些功能引角也可设置为普通的IO 端口使用。此外
它内部还集成了完整的模糊逻辑指令，可大大简化我们的程序设计。-Freescale s S12 family of single-chip microcomputer system hardware design, detail the use of single-chip hardware for the whole Chinese, MC9S12DG128B 16 Road AD conversion, the highest precision can be set to 10 are 8 and 8 PWM 22 Alliance for the 16-bit precision PWM, is particularly suitable for controlling multi-motor system. Its serial communication ports are also very rich 2-way SCI, 2 road SPI in addition to IIC, CAN bus, such as ports, and using the primers angle multiplexing function, so that these functions can also be cited angle is set to normal IO port to use. In addition, it also integrates the internal integrity of the fuzzy logic instructions, can greatly simplify the design of our procedures.
- 2022-09-14 18:20:03下载
- 积分：1
-
1．熟悉硬件仿真工具KD30的使用。 2．修改样本程序 SAMP1a，使无论在计数或停止计数时，按 SW3 均对计数值清零，并停止计数。 3．编制一个秒表程序,...
1．熟悉硬件仿真工具KD30的使用。 2．修改样本程序 SAMP1a，使无论在计数或停止计数时，按 SW3 均对计数值清零，并停止计数。 3．编制一个秒表程序, 测试精度为0.1秒，按 SW1键启动计数，再按一次 SW1键停止计数。任何时候按 SW3 键停止计数，并对计数值清零。 4．按 SW1键后， 以 0.1 秒为单位开始计数，再按一次 SW1 键停止计数。若按 SW1 键时间超过2秒，则计数值清零，回到初始状态。-1. Familiar with the hardware simulation tool KD30 use. 2. Revised procedures SAMP1a samples, regardless of the count or counts at the end, according to SW3 numerical terms were right, reset, and stop counting. 3. Preparation of a stopwatch procedures, testing accuracy of 0.1 seconds, according to bond SW1 start counting, according to a key SW1 stopped counting. By SW3 any time to stop counting bond and reset the count. 4. By SW1 bond, after 0.1 seconds for start counting, according to a key SW1 stopped counting. If SW1 keys by the time more than two seconds, then reset the count and return to the initial state.
- 2023-08-01 05:40:03下载
- 积分：1
