登录
首页 » SCM » Single

Single

于 2022-03-10 发布 文件大小:983.00 B
0 145
下载积分: 2 下载次数: 1

代码说明:

单片机键盘阵列扫描源程序解析,让你更好的理解按键扫描的原理-Single-chip arrays to scan the source code to resolve the keyboard, allows you to better understand the key principle of scanning

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • 用于上位机和下位机通信的人机界面及串口接口程序
    用于上位机和下位机通信的人机界面及串口接口程序-For the upper and lower man-machine communication interface and serial interface program
    2022-03-11 13:28:15下载
    积分:1
  • 用于MSP430F247单片机的NOKIA5110液晶屏驱动程序
    用于MSP430F247单片机的NOKIA5110液晶屏驱动程序-NOLIA 5110 LCD Driver For MSP430F247
    2022-01-28 06:19:28下载
    积分:1
  • 三相步进电机的三相六拍工作方式,正转的绕组通电顺序:A、AB、B、BC、C、CA、A,反转的通电顺序:A、AC、C、CB、B、BA、B、A。 由于步进电机转子有一定的惯性以及所带负载的惯性,故步进电机的工作过程中不能及时的启动和停止,在启动时应慢慢的加速到预定速度,在停止前应逐渐减速到停止,否则,将产生失步现象。 步进电机的控制问题可总结为两点: 1、产生工作方式需要的时序脉冲; 2、控制步进电机的速度,使它始终遵循加速、匀速、减速的规律工作。 -Three-phase three-phase stepper motor six shot work, is to order the winding power: A, AB, B, BC, C, CA, A, reverse the order of power: A, AC, C, CB, B, BA, B, A. As the stepper motor rotor has a certain degree of inertia, as well as brought about by the inertia load, the stepper motor during the course of work should not start and stop time, start to be slowly accelerated to a predetermined speed, the stop should be to slow down gradually to the stop, otherwise, will result in out-of-step phenomenon. Stepper motor control problems can be summarized in two points: one, resulting in the need to work the timing pulse 2, control the speed of stepper motor, so that it always followed acceleration, velocity, deceleration of the law of the work.
    2022-07-20 15:21:46下载
    积分:1
  • ICCavr编写的TWI总线协议读写函数,测试通过
    ICCavr编写的TWI总线协议读写函数,测试通过-ICCavr prepared by TWI bus protocol to read and write function, the test
    2022-04-20 15:42:20下载
    积分:1
  • AD0832程序 基本详细,比较适用于单片机的连接,等等,用C语言编写,较有参考价值...
    AD0832程序 基本详细,比较适用于单片机的连接,等等,用C语言编写,较有参考价值-AD0832 basic procedures in detail, compared to the MCU connected, and so on, using C language, a reference value
    2022-04-01 09:40:48下载
    积分:1
  • usb程序 硬件用的是isp1518,传输方式dma
    usb程序 硬件用的是isp1518,传输方式dma-usb hardware procedure is used isp1518, transmission dma
    2022-07-02 20:10:19下载
    积分:1
  • 点阵16x64 C51源程序+仿真 点阵16x64 C51源程序+仿真
    点阵16x64 C51源程序+仿真 点阵16x64 C51源程序+仿真-16x64 C51 lattice source+ Simulation lattice 16x64 C51 source+ Simulation
    2022-01-28 21:10:23下载
    积分:1
  • MT8888芯片的C51读写程序
    MT8888芯片的C51读写程序-MT8888 chip C51 literacy procedures
    2022-09-02 08:50:02下载
    积分:1
  • 这是我校用于课程设计的USB单片机的库函数。内容精彩,不可多得。...
    这是我校用于课程设计的USB单片机的库函数。内容精彩,不可多得。-This is my school curriculum design for the USB MCU library functions. As exciting indeed.
    2022-03-22 13:41:19下载
    积分:1
  • 基于单片机与FPGA的DDS程序代码,产生任意波形
    基于单片机与FPGA的DDS程序代码,产生任意波形-DDS-based MCU with FPGA-code, resulting in arbitrary waveform
    2022-04-23 14:49:58下载
    积分:1
  • 696518资源总数
  • 106161会员总数
  • 5今日下载