-
IC Card operating software : AT88SCl604 chip mode of operation there are five. T...
IC卡操作软件:AT88SCl604芯片的操作模式有五种。它们是通过配PGM、RST、CLK等引脚信号及内部地址计数器(IAC)的状态组合来实现。 (1) 芯片复位操作： AT88SCl604有两种复位方式:上电复位和控制复位。 上电复位： 上电复位是当芯片加电时的最初状态。上电复位属于芯片 内部复位。它将使芯片内部所有的隐含标志复位到"0"状态。并使地址计数器复位到0位。 控制复位： 当CLK为低时，在RST脚上的一个下降沿将便芯片产生复位操作。 控制复位是将地址计数器复位到0位，而不影响任何内部标志的状态。-IC Card operating software : AT88SCl604 chip mode of operation there are five. They are allocated by PGM, RST, etc. pin CLK signal and the internal address counter (IAC) portfolio of the state is to be achieved. (1) chip reset operation : reduction AT88SCl604 two ways : power-on reset and reset control. Power-on reset : power-on reset when the chip is in power at the initial state. Power-on reset the internal chip is reset. It will enable all internal chip implied signs reset to "0" state. Make address counter reset to 0. Reset control : When the CLK for the low, the RST feet of a falling edge chips will have to reset operation. Reset control is to address counter reset to 0, without prejudice to any signs of internal sta
- 2022-05-28 08:23:00下载
- 积分：1
-
SCM is the multi
这个是单片机多路数据采集的控制程序。并可以同时多路输出。-SCM is the multi-channel data acquisition control procedures. And can more output.
- 2022-06-12 15:24:46下载
- 积分：1
-
周立功的LPC214X关于中断捕获查询实验.
周立功的LPC214X关于中断捕获查询实验.-Ligong LPC214X weeks of inquiries concerning the interruption of capture experiments.
- 2022-08-10 00:33:02下载
- 积分：1
-
usb 68013A芯片原理图和PCB图
usb 68013A芯片原理图和PCB图-usb 68013A chip and PCB schematic diagram
- 2022-01-25 19:22:22下载
- 积分：1
-
ATmega8
ATmega8-使用Protues仿真,让你不用开发板也可以学到单片机.-ATmega8-use Protues simulation, so you do not have development board can also be learned Singlechip.
- 2022-03-15 08:51:50下载
- 积分：1
-
This is the Philips chip tea5767 fm driver
这是philips 公司的fm 芯片tea5767的驱动程序-This is the Philips chip tea5767 fm driver
- 2023-07-06 10:00:02下载
- 积分：1
-
这是一个keil c51 程序 采用8031单片机，是一个学习keil c 的入门级程序...
这是一个keil c51 程序 采用8031单片机，是一个学习keil c 的入门级程序-This a procedure used Keil decoder 8031 is a study Keil c entry-level procedures
- 2023-05-19 19:30:04下载
- 积分：1
-
This an MCU
这是一个基于MCU的电机控制系统，单片机接收PC的信息，根据Modbus通信协议转换为相应电机控制命令。 整个程序在keil环境下开发，实现了电机的启动、停止、增速、减速、反馈运行时间和速度的功能。-This an MCU-based motor control system, the 8031 PC receiving the information, according to Modbus communication protocol conversion to the corresponding motor control commands. Keil in the whole process environment in development and the launch of the motor, stop, the growth rate, deceleration, feedback running time and speed functions.
- 2022-07-08 16:27:25下载
- 积分：1
-
单片机构建环境功能齐全，操作简单，适合初学者
单片机的编译环境 功能齐全，操作简单，适合初学者使用-SCM build environment fully functional, simple operation, for beginners
- 2023-05-15 08:30:03下载
- 积分：1
-
gps全球定位系统定位数据的提取，协议：nmea0183
gps全球定位系统定位数据的提取，协议：nmea0183-a GPS global positioning system location data extraction, agreements : nmea0183
- 2023-05-04 20:00:03下载
- 积分：1
