登录
首页 » SCM » dds 信号发生器的参考程序,,精工参考

dds 信号发生器的参考程序,,精工参考

于 2022-03-17 发布 文件大小:1.09 kB
0 194
下载积分: 2 下载次数: 1

代码说明:

dds 信号发生器的参考程序,,精工参考-dds reference signal generator procedures, Seiko reference

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • AVR Studio下开发的CAN
    AVR Studio下开发的CAN-232串口通信代码,硬件平台为AT90CAN,已通过测试~-AVR Studio developed under the CAN-232 serial communication code, the hardware platform for AT90CAN, has been tested to be ~
    2022-05-13 03:57:30下载
    积分:1
  • 华为、上海贝尔、台湾神达电脑电路板PCB布线规则,对…
    华为、上海贝尔、台湾神达电脑的电路板PCB布线的规范,对跨入电路板硬件设计领域是一个捷径,养成良好的布局布线习惯将受益无穷啊,三家公司的布线规范供你参考-Huawei, Shanghai Bell, Taiwan Mitac computer circuit board PCB routing rules, on the threshold of the circuit board hardware design area is a shortcut, to develop good habits will benefit from placement and routing infinite ah, the three companies wiring specification for your reference
    2022-01-26 05:02:27下载
    积分:1
  • 英飞凌C166之XC164CS按钮键盘扫描程序
    英飞凌C166之XC164CS按钮键盘扫描程序-Infineon C166
    2023-02-12 23:15:03下载
    积分:1
  • 用汇编语言实现数据采集,数据显示,数据通信(2543,7279等芯片),是我做的毕设题目...
    用汇编语言实现数据采集,数据显示,数据通信(2543,7279等芯片),是我做的毕设题目-assembly language for data acquisition, data, data communications (2543,7279 chip), I do BI located topic
    2022-03-29 20:31:31下载
    积分:1
  • c51的usb的通信程序库,支持51兼容的单片机和pdusbd12接口芯片
    c51的usb的通信程序库,支持51兼容的单片机和pdusbd12接口芯片-C51 s usb communication library to support the 51-compatible MCU and pdusbd12 interface chip
    2022-05-18 12:19:07下载
    积分:1
  • MEGA16 驱动开发板上的继电器,按不同的独立键,交替改变继电器开关状态...
    MEGA16 驱动开发板上的继电器,按不同的独立键,交替改变继电器开关状态-mega16 drive PWM
    2022-01-22 05:32:39下载
    积分:1
  • 基于at89c52的乒乓球游戏系统,全部通过lcd菜单选择,通过proteus仿真(绝对可行)...
    基于at89c52的乒乓球游戏系统,全部通过lcd菜单选择,通过proteus仿真(绝对可行)-err
    2023-01-25 03:25:04下载
    积分:1
  • c51primer
    c51primer
    2022-08-15 00:28:47下载
    积分:1
  • 用于实现对液晶进行显示控制以及对键盘进行扫描识别,同时完成数据传输...
    用于实现对液晶进行显示控制以及对键盘进行扫描识别,同时完成数据传输-used to achieve for the LCD display and control of the keyboard scan identification, complete data transmission
    2022-04-29 23:58:41下载
    积分:1
  • MCS
    MCS-51单片机有5个中断源,其中两个是由-INT0、-INT1引脚输入的外部中断源;另外三个是内部中断源即由T0、T1的溢出引起中断和串行口发送完一个字节或接收到一个字节数据引起中断。触发外部中断有两种方式,即下降沿引起中断或低电平引起中断。当编程TCON中的ITi(i=0、1)为1时,则引起触发的方式为边沿触发方式,反之(ITi=0)为低电平触发方式。每个中断源的中断请求能否得到响应要受两级“开关”的控制,即一个总“开关”-MCS-51 single-chip has five interrupt sources, two of which are by-INT0,-INT1 pin input external interrupt source the other three internal interrupt sources from the T0, T1 overflow caused by the disruption and serial port sending or receiving end of a byte to a byte of data caused by interruption. Triggered external interrupt has two modes, namely, falling edge or low-level disruption caused disruption caused. When programming TCON in ITi (i = 0,1) for the 1:00 has been the subject of a way to trigger the way to the edge of the trigger, on the contrary (ITi = 0) for low-level trigger mode. Each interrupt source interrupt request can be subject to levels in response to
    2023-07-06 00:00:03下载
    积分:1
  • 696518资源总数
  • 106161会员总数
  • 5今日下载