-
义隆仿真器使用资料,全中文资料，希望能对学习义隆单片机的朋友有一点帮助。...
义隆仿真器使用资料,全中文资料，希望能对学习义隆单片机的朋友有一点帮助。-Elan simulator and use the information, the English data, Elan hopes to study single-chip microcomputer has a little friend to help.
- 2023-06-12 00:00:03下载
- 积分：1
-
Provide the operations include Read and Write to the AT25320A, SPI
Provide the operations include Read and Write to the AT25320A, SPI-interface EEPROM with 32k bits,ATMEL Icn.-Provide the operations include Read and Wr/ite to the AT25320A. SPI-interface EEPROM with 32k bits, ATMEL Icn.
- 2023-07-18 03:40:02下载
- 积分：1
-
Ti 公司低功耗RF芯片选型资料.其中有13.56
Ti 公司低功耗RF芯片选型资料.其中有13.56-27MHz,300-1000MHz ,2.4GHz等等芯片选型参考-Ti low-power RF chip companies Selection information. Among them, 13.56-27MHz ,300-1000MHz, 2.4GHz chip, etc. Selection of reference
- 2022-02-16 05:55:48下载
- 积分：1
-
PROFIBUS现场总线，RS485
profibus TO RS485
profibus TO RS485
- 2022-02-19 22:06:37下载
- 积分：1
-
SCI的代码
基于飞思卡尔16位单片机的的串行通信SCI程序-SCI code
- 2022-07-14 12:27:00下载
- 积分：1
-
数控电源的LCD菜单程序，实现数控电源液晶菜单显示
数控电源的LCD菜单程序，实现数控电源液晶菜单显示-CNC Power Supply LCD menu procedures, NC Power LCD menu display
- 2023-03-01 02:05:03下载
- 积分：1
-
ad0809 some procedures can be used as a number of learning data entry
ad0809一些程序，可以当做入门的一些学习资料-ad0809 some procedures can be used as a number of learning data entry
- 2022-08-17 01:13:49下载
- 积分：1
-
6段数码管分别显示，时，分，秒，四个按键，K1（P0.0），K2（P0.1），
K3（P0.2），K4（P0.3），四个按键用来调时间的，按下K1，所有位都...
6段数码管分别显示，时，分，秒，四个按键，K1（P0.0），K2（P0.1），
K3（P0.2），K4（P0.3），四个按键用来调时间的，按下K1，所有位都清零显示，然后按下K2，秒在闪烁，继续按K2分闪烁，不段地按K2 秒--分--时切换着闪烁，在某位闪时按下K3相应位加一，确认调整，按K4，取消调整再按K1。在K1按下以后才有调时的功能，如果K1没有按下，按别的键没有反映。这为了在加点按键功能留着用
-6 respectively of the digital control, when, minutes and seconds, four keys, K1 (P0.0). K2 (P0.1), K3 (P0.2), K4 (width), the four keys to the transfer time, press the K1, All spaces are reset, then press K2, the scintillation seconds, according to K2 pm flickered. not according to K2 of seconds-- minutes-- when switching to flicker in certain press the flash-K3 corresponding increase in a confirmed adjustment by K4, then canceled K1 adjustment. K1 in the press will only be made after the transfer of function, if K1 pressed by other key is not reflected. This points to the function keys used Retention
- 2022-08-13 14:18:02下载
- 积分：1
-
这是一个CAN总线通信的节点程序，是我自己编写的，希望指正。...
这是一个CAN总线通信的节点程序，是我自己编写的，希望指正。-This is a CAN bus communication nodes procedures, the preparation of my own, and I hope correct me.
- 2022-12-22 07:45:03下载
- 积分：1
-
MDT MCU Development Tools Collection (267K) mdttool.zip
MDT单片机开发工具大全(267k)mdttool.zip-MDT MCU Development Tools Collection (267K) mdttool.zip
- 2022-02-25 02:24:42下载
- 积分：1
