登录
首页 » SCM » 2.4G wireless module nrf2401 small allocation procedures. [Nrf2401

2.4G wireless module nrf2401 small allocation procedures. [Nrf2401

于 2022-03-18 发布 文件大小:31.38 kB
0 192
下载积分: 2 下载次数: 1

代码说明:

2.4G无线模块nrf2401配置的小程序! [nrf2401-source-code-for-AVR-8515.rar] - 这是NORDIC公司NRF2401基于AVR单片机的程序源代码-2.4G wireless module nrf2401 small allocation procedures. [Nrf2401- sourc e-code-for- AVR-8515.rar]- This is NORDIC company NRF24 Based on AVR 01 of the source code

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • 18b20显示程序,动态显示,调试通过.
    18b20显示程序,动态显示,调试通过.-18b20 display program, dynamic display, debugging through.
    2023-01-08 18:35:04下载
    积分:1
  • 硬盘MP3的详细资料
    硬盘MP3的详细资料-drive MP3 detailed information
    2023-04-04 20:15:03下载
    积分:1
  • 基于vriloge的数字钟具有调时、分、秒和定时报警功能,开发环境是MAXPUII的开发环境,实际检验是完全符合...
    基于vriloge的数字钟具有调时、分、秒和定时报警功能,开发环境是MAXPUII的开发环境,实际检验是完全符合-Vriloge based on the digital clock has adjusted hours, minutes, seconds and time alarm function, the development environment is MAXPUII development environment, the actual test is fully consistent with the
    2022-02-12 16:18:37下载
    积分:1
  • 本设计以P89V51RD2FN单片机为电动小车的控制核心,采用MSA
    本设计以P89V51RD2FN单片机为电动小车的控制核心,采用MSA-LD2.0倾角传感器实时测量跷跷板的倾斜角,用ST198光电传感器检测黑色引导线监测小车运动。光电传感器和倾角传感器模块把实时测量信号馈送至单片机,利用专用细分芯片TA8435H驱动步进电机,以脉宽调制式斩波方式对步进电机步进角进行细分,控制和调节小车速度。采用增量式PID控制算法确保小车能够达到平衡;用RT128×64M液晶显示时间、角度等参数。经测试表明:小车各项性能指标达到设计要求,能够实现30秒内小车行驶到规定点,并保持跷跷板平衡;在跷跷板一端配重可调整的情况下,小车也能自动找到平衡点并保持跷跷板平衡。-The single-chip design for the electric car P89V51RD2FN control of the core, the MSA-LD2.0 seesaw angle sensor real-time measurement of the tilt angle, the detection of black ST198 photoelectric sensor to monitor vehicle movement and guide lines.Photoelectric sensors and angle sensors in real-time measurement module to feed the signal to the microcontroller, using a dedicated sub-chip stepper motor driver TA8435H to PWM chopper-type stepper motor on the sub-stepping angle, control and regulation vehicle speed. The use of incremental PID control algorithm to ensure that the car can achieve balance with LCD RT128 × 64M time, angle and other parameters.After the test showed that: the performance car
    2023-09-02 02:10:04下载
    积分:1
  • 为单片机C51程序,用来控制数控机床的运行
    为单片机C51程序,用来控制数控机床的运行--A SCM C51 program. It controls the operation of numerically controlled machine.
    2022-10-09 11:20:02下载
    积分:1
  • 自编的C51串口通讯程序,在AT89C51上测试运行OK,用22.1M晶振最高可跑115KBPS...
    自编的C51串口通讯程序,在AT89C51上测试运行OK,用22.1M晶振最高可跑115KBPS-directed the C51 serial communications procedures, the AT89C51 OK on the test run, with a maximum 22.1M crystal run 115KBPS
    2022-10-02 02:15:03下载
    积分:1
  • C Flash Drivers for the AT89C51RD2_ED2_ID2 for Keil Compiler rev 1
    C Flash Drivers for the AT89C51RD2_ED2_ID2 for Keil Compiler rev 1
    2022-03-19 09:56:56下载
    积分:1
  • 基于1335的液晶驱动程序1,本全程应用于安得利160×160液晶
    基于1335的液晶驱动程序1,本全程应用于安得利160×160液晶-Based on the 1335 driver of the LCD 1, the full benefit applies to an 160 × 160 LCD
    2022-03-26 05:46:51下载
    积分:1
  • 16位按键扫描程序,包含数字钟计时,闹钟报警,及定时应用
    16位按键扫描程序,包含数字钟计时,闹钟报警,及定时应用-16 button scanning procedures, including digital clock timer, alarm clock, alarm, and timing applications
    2023-05-17 09:45:03下载
    积分:1
  • 实现三线控制LCD1602,并附有相关c程序,是一电子设计模块,在减少使用接口方面非常实用...
    实现三线控制LCD1602,并附有相关c程序,是一电子设计模块,在减少使用接口方面非常实用-The realization of three-wire control LCD1602, with c-related procedures, is a electronic design modules, to reduce the use of interfaces in a very practical
    2022-05-15 06:33:25下载
    积分:1
  • 696516资源总数
  • 106913会员总数
  • 8今日下载