登录
首页 » 嵌入式系统 » 这是一个MSP430在IAR环境下开发的益而高点亮LCD的一个小程序...

这是一个MSP430在IAR环境下开发的益而高点亮LCD的一个小程序...

于 2022-03-19 发布 文件大小:1.14 kB
0 190
下载积分: 2 下载次数: 1

代码说明:

这是一个MSP430在IAR环境下开发的益而高点亮LCD的一个小程序-This is a MSP430 in the IAR environment benefits the development of high-lit LCD and a small program

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • 基于wince的简单计算器
    这是在wince下的一个简易计算器代码,实现加减乘除 三角函数的运算 并且可以显示三角函数图形
    2022-06-18 11:20:11下载
    积分:1
  • These are commonly used in communications equipment circuit schematics, many of...
    这些都是常用的通信设备的电路原理图,很多是高频电子线路的-These are commonly used in communications equipment circuit schematics, many of them are high-frequency electronic circuits
    2022-01-28 10:01:08下载
    积分:1
  • 利用WinDriver开发的USB驱动程序源代码,
    利用WinDriver开发的USB驱动程序源代码,-WinDriver development using USB driver source code,
    2022-10-08 09:45:03下载
    积分:1
  • 红外遥控码的接收程序,适用于pt2222,nec 6211 等
    红外遥控码的接收程序,适用于pt2222,nec 6211 等--Receiver program for remote infrared encoding. It could be used in pt2222, nec 6211, and etc.
    2023-07-12 23:35:03下载
    积分:1
  • OCM4X8C驱动 作者:孙新虎 sunxinhu@163.com 日期:200412
    OCM4X8C驱动 作者:孙新虎 sunxinhu@163.com 日期:200412-OCM4X8C drive Author : Sun tiger sunxinhu@163.com date : 200412
    2022-03-23 00:09:48下载
    积分:1
  • 主要介绍了使用MTV230芯片的开发,如何实现程序的烧写等
    主要介绍了使用MTV230芯片的开发,如何实现程序的烧写等-Mainly introduces the use of MTV230 chip development, the programmer how to program, etc.
    2022-03-20 17:14:02下载
    积分:1
  • 声卡正弦波音频信号发生器源代码。钱钱不够的兄弟可以考虑使用。...
    声卡正弦波音频信号发生器源代码。钱钱不够的兄弟可以考虑使用。-audio sine wave signal generator audio source. Money enough money to the brothers may consider using.
    2022-04-17 04:52:23下载
    积分:1
  • STM32 USART2中断接收
    基于STM32F107的 USART2串口中断接收的例程 可以直接应用于实际项目中 采用USART2实现串口通信 请点击左侧文件开始预览 !预览只提供20%的代码片段,完整代码需下载后查看 加载中 侵权举报 打分 发表评论 暂无评论
    2022-08-26 10:27:38下载
    积分:1
  • I2C总线驱动。与成功测试。实现多字节存储
    I2C总线驱动。与成功测试。实现多字节存储-I2C bus driver. And successfully tested. Multi-byte storage
    2022-10-12 05:40:03下载
    积分:1
  • AT91RM9200的USB host和USB device的代码ADS1.2. USB
    AT91RM9200的USB host和USB device的代码ADS1.2. USB-Device测试程序: 因为程序运行在SDRAM中,所以要先初始化SDRAM(可用basic boot程序初始,之后不能复位或断电),再运行此程序,程序运行后连接USB端口,计算机会提示检测到新硬件,安装硬件驱动程序atmusb6119.inf 后计算机会把USB端口虚拟为一个串行的端口使用-AT91RM9200 the USB host and USB device code ADS1.2.USB-Device test procedure: Because the procedure is running in SDRAM, and so we have to initialize SDRAM (available for the initial basic boot procedure, followed by Can not reset or power off), then Run this program, the program to run after connecting USB port, the computer will be prompted to detect the new hardware, installing hardware drivers after the computer will atmusb6119.inf virtual USB port to a serial port to use
    2022-01-30 16:36:24下载
    积分:1
  • 696516资源总数
  • 106913会员总数
  • 8今日下载