-
1520 controller using dot matrix LCD module 12232 51 C MCU control code keil com...
使用1520控制器的12232点阵液晶模块的51单片机控制C代码,keil编译通过,使用端口直接连接方法,P1口为数据口,控制线在P3部分端口-1520 controller using dot matrix LCD module 12232 51 C MCU control code keil compiled by the use of ports directly connected, I P1 for data export, the line of control in some ports P3
- 2022-10-13 16:30:02下载
- 积分：1
-
LCD driver source, the microcontroller is AT89C52.
这是JHD19264液晶显示器的驱动源程序，单片机采用的是AT89C52.-LCD driver source, the microcontroller is AT89C52.
- 2022-08-15 01:14:47下载
- 积分：1
-
Sunplus most of the ultrasonic ranging modules, 40KHz generated through 555 of t...
凌阳最出的超声波测距模组，通过555产生40KHz的超声波，有SPE061A单片机控制超声波的发射和接收，最初的版本在程序方面比第二版本来得简单，主要是通过了硬件电路减少了程序，附电路图、PCB图等-Sunplus most of the ultrasonic ranging modules, 40KHz generated through 555 of the ultrasound, ultrasound has SPE061A single-chip microcomputer to control the transmitting and receiving an initial version of the procedure than the second version is more simple, mainly through the reduction of hardware circuit procedures, with schematics, PCB map
- 2022-07-12 03:51:44下载
- 积分：1
-
时钟芯片ds1302 程序
源程序按版本号放在文件夹中。里面有在Protues中仿真的DSN文件。
打开MPLAB的MCP文件进行编译
将DSN文件...
时钟芯片ds1302 程序
源程序按版本号放在文件夹中。里面有在Protues中仿真的DSN文件。
打开MPLAB的MCP文件进行编译
将DSN文件载入Protues中
将生成的HEX导入到Protues中的16F84A中 -> RUN-Clock chip DS1302 procedures in accordance with the version number on the source folder. Protues there are in the DSN file in the simulation. Open the MPLAB compiler of the MCP file DSN file loading will be generated by HEX will Protues into Protues in 16F84A in-
- 2022-02-07 10:24:45下载
- 积分：1
-
also uses a PID temperature control, and my door is different D/A output volume...
也用到了温度PID控制,和我门的不同是采用D/A输出控制量的.主要由温度采样--->温度滤波子程序--->温度线性化----->温度设定值等模块组成.-also uses a PID temperature control, and my door is different D/A output volume control. By sampling temperature--- gt; Temperature filter subroutine-- gt; Temperature linear----- gt; The temperature setpoint and other modules .
- 2023-08-03 04:10:02下载
- 积分：1
-
ad9833的原理图和源程序，希望对需要的人有用
ad9833的原理图和源程序，希望对需要的人有用-AD9833 Schematic and source of hope for those who need it useful
- 2022-04-10 16:10:37下载
- 积分：1
-
短信息相关单片机GSM短消息控件
短信息相关单片机GSM短消息控件-short information related SCM GSM Short Message Control
- 2022-12-26 01:45:03下载
- 积分：1
-
用keil c编写的PID算法,不错噢.
用keil c编写的PID算法,不错噢.-with keil c prepared by the PID algorithm, Oh Yes. Ha ha
- 2022-03-10 17:50:19下载
- 积分：1
-
利用动态扫描和定时器1在数码管上显示
出从765432开始以1/10秒的速度往下递减
直至765398并保持显示此数，与此同时利
用定时器0以500...
利用动态扫描和定时器1在数码管上显示
出从765432开始以1/10秒的速度往下递减
直至765398并保持显示此数，与此同时利
用定时器0以500MS速度进行流水灯从上至
下移动，当数码管上数减到停止时，实验
板上流水灯也停止然后全部开始闪烁，3秒
后（用T0定时）流水灯全部关闭、数码管上
显示出"HELLO"。到此保持住。
设晶振频率为12MHz。-The use of dynamic scanning and Timer 1 in the digital control to show from the beginning of 765,432 to 1/10 seconds until the speed of descending down 765,398 and maintain display this number, at the same time the use of Timer 0 to 500ms the speed of light from the flowing water to Under the move, when reduced to a few digital tube stop, the experiment on-board water stop and then all the lights started to flicker, 3 seconds later (T0 regularly used) closed water lights, digital tubes show
- 2022-02-03 00:14:56下载
- 积分：1
-
U盘(实际是USB SD卡读卡器)的制作方案。 硬件构成：ATmega168+PDIUSBD12+SD
内附GCC源码和原理图。
开发环境是AvrSt...
U盘(实际是USB SD卡读卡器)的制作方案。 硬件构成：ATmega168+PDIUSBD12+SD
内附GCC源码和原理图。
开发环境是AvrStudio4.13 b528 + WinAVR200701-U disk (actually USB SD card reader) production program. Hardware: ATmega168+ PDIUSBD12+ SD containing GCC source code and schematics. Development environment is AvrStudio4.13 b528+ WinAVR200701
- 2023-07-13 03:50:04下载
- 积分：1
