-
ARM since learning some lessons learned, in their own design S3C44B0X an example...
本文是我学习ARM开发以来的一些经验总结，以自己设计的S3C44B0X板为例，给出我调试开发ARM开发板的一些最基础知识。我只是在自己的开发板调试过并且经验有限，有些知识只能做为参考，不一定准确，就算给大家一个“例程”吧，如果大家有不同意见，希望多多指正！-ARM since learning some lessons learned, in their own design S3C44B0X an example, I presented the development and debugging of the ARM development board some of the most basic knowledge. I was only in their own development boards tuned and limited experience, some knowledge only as a reference, not necessarily accurate, even if everyone with a "routine" for the country, if we have different opinions, many correct!
- 2022-05-21 03:33:43下载
- 积分：1
-
基于arm―LPC2103的LCD602的驱动程序，有proteus仿真。
基于arm―LPC2103的LCD602的驱动程序，有proteus仿真。-The arm-LPC2103-based LCD602 driver has Proteus simulation.
- 2022-08-22 15:59:04下载
- 积分：1
-
SDT环境下，基于S3C4510的GDMA模块使用，可用
SDT环境下，基于S3C4510的GDMA模块使用，可用-SDT environment, based on the S3C4510 module GDMA use, available
- 2022-01-27 17:26:11下载
- 积分：1
-
2812使用spi读写fm25cl64或者at25640的程序，已经测试通过。注意在在eeprom的datasheet中都写只支持spi的0或者3模式，但我用0...
2812使用spi读写fm25cl64或者at25640的程序，已经测试通过。注意在在eeprom的datasheet中都写只支持spi的0或者3模式，但我用0模式一直调不通，改用spi模式才可以，程序中就是使用spi的1模式。-2812 to read and write using spi or at25640 procedures FM25CL64 have the test. Attention to the datasheet in the EEPROM are write only support spi mode 0 or 3, but I used the 0 model has been adjusted barrier before they can switch to spi mode, process is the use of one mode of spi.
- 2022-01-25 21:08:07下载
- 积分：1
-
•STM32F4xx
“闪亮”项目是一个简单的CMSIS RTOS的例子
- 2022-03-29 05:27:39下载
- 积分：1
-
LPC213X under the graphical interface (Embedded GUI) running on UC/COS systems.
LPC213X下的 图形界面（嵌入式GUI)，运行在UC/COS系统下。-LPC213X under the graphical interface (Embedded GUI) running on UC/COS systems.
- 2023-07-07 22:40:02下载
- 积分：1
-
his project was built and tested with WinAVR
his project was built and tested with WinAVR-20060125.
Make sure the MCU target define in the Makefiles corresponds to the AVR you are using!!
To build the code, just install WinAVR and run "make" from the console in echomaster and
echoslave subdirs.
"make program" will program the device if you have a AVRISP attached.
Remember to set the AVR device to at least 8MHz. The AVR may use the programmable clock
from MC1319x, just remember to check if the MC1319x and SPI communication is working FIRST!
Otherwise you wont get any clock signal to the AVR and then you can t program it or reset
the fuses!
The MC1319x has default clock output of 32kHz so you will have to set your programmer to
a very low frequency (
- 2023-02-22 21:55:03下载
- 积分：1
-
uda1341中文详细使用说明以及WAV的格式介绍
uda1341中文详细使用说明以及WAV的格式介绍-uda1341 detailed instructions in Chinese, as well as WAV format description
- 2023-02-14 22:30:04下载
- 积分：1
-
ezflash_x5 jtag program
ezflash_x5 jtag program
- 2023-08-19 18:30:03下载
- 积分：1
-
AT91M42800A的bootloader源代码，实现了中断处理以及中断矢量。
AT91M42800A的bootloader源代码，实现了中断处理以及中断矢量。-RISC Bootloader source code, achieve interruption of treatment and interrupt vectors.
- 2022-11-02 22:35:03下载
- 积分：1
