-
采用IAR在线调试ADI基于ARM7内核的ADUC7026的RAM_CODE
采用IAR在线调试ADI基于ARM7内核的ADUC7026的RAM_CODE-IAR debug using online ADI based on ARM7 core ADUC7026 the RAM_CODE
- 2023-06-29 14:00:04下载
- 积分:1
-
HT1621 is a 128
HT1621 是一款128 个位元的LCD 控制器件,内部RAM 直接对应LCD 的显示单元。相应的软件使它适用于包括LCD 模块和显示子系统在内的多功能应用。主控制器与HT1621接口只需4 到5 根线。内置的省电模式极大的降低了功耗。本文介绍HT48R05A-1 单片机来控制HT1621,并介绍如何turn ON 及turn OFF LCD 所有位元。-HT1621 is a 128-bit LCD control device, the internal RAM directly correspond to the LCD display unit. So that it applies to the appropriate software, including LCD modules and display sub-systems, including multi-purpose applications. Master controller and the HT1621 interface only 4-5 lines. Built-in power-saving mode greatly reduce power consumption. This article describes the HT48R05A-1 microcomputer to control the HT1621, and describes how to turn ON and turn OFF LCD all the bits.
- 2022-03-14 07:37:57下载
- 积分:1
-
C8051F040 operation timing of the HT1380, as well as set
C8051F040的HT1380操作时序,以及时间设置和LCD时间显示(显示小时和分钟)-C8051F040 operation timing of the HT1380, as well as set-up time and time LCD display (shows hours and minutes)
- 2022-05-21 07:05:24下载
- 积分:1
-
51单片机控制的电动自行车驱动系统源程序(CHUNTIAN)
51单片机控制的电动自行车驱动系统源程序(CHUNTIAN)
-51 microcomputer control drive system for electric bicycle source (CHUNTIAN)
- 2022-01-21 17:59:12下载
- 积分:1
-
LM3S101单片机模拟I2C
本模拟I2C软件包包含了I2C操作的底层函数,如发送数据及接收数据,应答位发送,并提供了几个直接面对器件的操作函数,它很方便...
LM3S101单片机模拟I2C
本模拟I2C软件包包含了I2C操作的底层函数,如发送数据及接收数据,应答位发送,并提供了几个直接面对器件的操作函数,它很方便的与用户程序连接并扩展.
- 2023-03-25 13:30:03下载
- 积分:1
-
关于无刷直流电机的仿真,该程序说明了如何进行无刷直流电机的仿真...
关于无刷直流电机的仿真,该程序说明了如何进行无刷直流电机的仿真-Brushless DC motor on the simulation, the program explains how to carry out the simulation BLDCM
- 2022-01-30 16:31:25下载
- 积分:1
-
正弦波发生器大运用阿斯达是法国阿双方 威尔uweyr 饿efw98ur wef8u...
正弦波发生器大运用阿斯达是法国阿双方 威尔uweyr 饿efw98ur wef8u-sinwave founcation
- 2022-01-28 01:38:36下载
- 积分:1
-
C8051F020的LCD的驱动程序,包括画图的一些例程
C8051F020的LCD的驱动程序,包括画图的一些例程-C8051F020 the LCD driver, including drawing a number of routines
- 2022-12-10 06:00:03下载
- 积分:1
-
keilc+ proteus light parallel port design of experiments requirements: master th...
keilc + proteus
并行口设计指示灯实验
要求:掌握80C51单片机输入输出接口使用方法
学会开关量输入输出控制的接口技术及编程方法
实验题目:8个发光二极管D1~D8分别接在单片机P1.0-P1.7端口上,一个开关接在P3.0上。要求输出端口输出 “0”时,发光二极管亮。开关闭合时,开始按P1.0-P1.1-...-P1.7的顺序依次点亮LED,再按 P1.7-P1.6 -...-P1.0的顺序点亮LED,重复循环。开关断开时,立刻停止点亮指示灯。-keilc+ proteus light parallel port design of experiments requirements: master the 80C51 microcontroller input and output interfaces Society of switch to use the amount of input and output control interface technology and programming methods Experimental subjects: eight light-emitting diodes D1 ~ D8, respectively connected to the MCU P1.0-P1 .7 port on a switch connected to the P3.0 on. Requested output port output " 0" , the light-emitting diode light. Is closed, to embark on the P1.0-P1.1-...- P1.7 in the order light LED, and then P1.7-P1.6-...- P1.0 order light LED Repeat cycle. Switch off when the stop light indicator.
- 2022-11-16 18:10:03下载
- 积分:1
-
ATmega16 development environment AVR Singlechip ICC elevator control model (orig...
AVR单片机ATmega16
开发环境ICC
电梯控制模型 (原创)
测试成功-ATmega16 development environment AVR Singlechip ICC elevator control model (original) test successful
- 2022-12-27 05:55:03下载
- 积分:1