-
This is a drive LCM module shows the 51 single procedure, module lattice is 128...
这是一个驱动LCM模块显示的51单片程序,模块点阵是128×64,使用的IC是ST7565P.-This is a drive LCM module shows the 51 single procedure, module lattice is 128 64, the IC is ST7565P.
- 2022-05-05 02:37:19下载
- 积分:1
-
大家一起分享,一起努力,互相学习,共同进步
大家一起分享,一起努力,互相学习,共同进步-thank you
- 2022-01-28 05:09:18下载
- 积分:1
-
一个步进电机单片机控制程序,有电机正反转及加减速控制。...
一个步进电机单片机控制程序,有电机正反转及加减速控制。
- 2023-05-26 23:10:03下载
- 积分:1
-
常用串行EEPROM的编程应用,EEPROM是"Electrically Erasable Programmable Read...
常用串行EEPROM的编程应用,EEPROM是"Electrically Erasable Programmable Read-only"(电可擦写可编程只读存储器)的缩写,EEPROM在正常情况下和EPROM一样,可以在掉电的情况下保存数据,所不同的是它可以在特定引脚上施加特定电压或使用特定的总线擦写命令就可以在在线的情况下方便完成数据的擦除和写入-Commonly used application of serial EEPROM programming, EEPROM is Electrically Erasable Programmable Read-only (Xinhua EPROM) acronym, EEPROM under normal circumstances and EPROM, as in the case of power-down to save data , What is different is that it can exert in a particular pin on a specific voltage or use specific bus write command can be in the case of online data to facilitate the completion of the erase and write
- 2022-01-23 11:15:59下载
- 积分:1
-
c51学习使用的资料
有100多个原程序
c51学习使用的资料
有100多个原程序-decoder learning to use the data more than 100 original program
- 2022-05-07 07:46:45下载
- 积分:1
-
实时时钟芯片PCF8563 控制C51源程序
实时时钟芯片PCF8563 控制C51源程序-real-time clock chip PCF8563 source control C51
- 2022-03-21 23:34:21下载
- 积分:1
-
PIC 的资源,睡眠模式和看门狗的设置和使用的C语言样例
PIC 的资源,睡眠模式和看门狗的设置和使用的C语言样例-Using sleep mode, wakeup on change, and the watchdog timer
on baseline PICs
- 2023-02-04 07:25:03下载
- 积分:1
-
温度测量程序,包括显示、数据采集、进位、延时、数摸转换...
温度测量程序,包括显示、数据采集、进位、延时、数摸转换-temperature measurement procedures, including display, data acquisition, rounding, delay, a few touch conversion, etc.
- 2022-05-24 23:12:05下载
- 积分:1
-
kayan_yazi_48x7 led meseges
kayan_yazi_48x7 led meseges
- 2022-02-27 00:10:23下载
- 积分:1
-
PID是控制智能小车的经典算法在过程控制中,按偏差的比例(P)、积分(I)和微分(D)进行控制的PID控制器(亦称PID调节器)是应用最为广泛的一种自动控制器。...
PID是控制智能小车的经典算法在过程控制中,按偏差的比例(P)、积分(I)和微分(D)进行控制的PID控制器(亦称PID调节器)是应用最为广泛的一种自动控制器。它具有原理简单,易于实现,适用面广,控制参数相互独立,参数的选定比较简单等优点;而且在理论上可以证明,对于过程控制的典型对象──“一阶滞后+纯滞后”与“二阶滞后+纯滞后”的控制对象,PID控制器是一种最优控制-PID control of the smart car is the classic algorithm in process control, according to the percentage of deviation (P), Integral (I) and differential (D) control of PID controller (also known as PID regulators) is the most widely used as a automatic controller. It has simple, easy to realize, the application of a wide range of control parameters are independent of each other, the selection of relatively simple parameters, etc. and in theory can be proved that for a typical process control objects ─ ─
- 2022-03-14 12:37:53下载
- 积分:1