登录
首页 » SCM » Verilog realize the DDS sine wave signal generator and frequency measurement mod...

Verilog realize the DDS sine wave signal generator and frequency measurement mod...

于 2022-04-02 发布 文件大小:1.31 MB
0 278
下载积分: 2 下载次数: 1

代码说明:

Verilog实现的DDS正弦信号发生器和测频测相模块,DDS模块可产生两路频率和相位差均可预置调整的值正弦波,频率范围为20Hz-5MHz,相位范围为0°-359°,测量的数据通过引脚传输给单片机,单片机进行计算和显示。-Verilog realize the DDS sine wave signal generator and frequency measurement module test phase, DDS module can generate both frequency and phase difference can be preset to adjust the value of sine wave, frequency range of 20Hz-5MHz, phase range of 0 °-359 ° , measurement data and transmit them to the single-chip pin, single-chip microcomputer to calculate and display.

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • For equipment to monitor the working hours of the next
    用于设备工作时间监控的下位机源码,与计算机通信监控-For equipment to monitor the working hours of the next-bit machine source code, and computer communications monitoring
    2022-07-09 03:39:57下载
    积分:1
  • 9 Institute of accumulated data, we use a secret, please do not tell others!
    研究所积累的资料9,大家秘密使用,千万别告诉别人!-9 Institute of accumulated data, we use a secret, please do not tell others!
    2022-03-17 04:37:25下载
    积分:1
  • With the program AD9854C.exe one can set and tune the frequency in CW
    With the program AD9854C.exe one can set and tune the frequency in CW-mode. For use as a receiver LO also IF can be given and the both possible receiving frequencies are printed on the screen. The level in Q-outputs can be varied by giving the wanted attenuation in dB. This function is done by controlling a 12b digital multiplier in the device. In this case the level decreases somewhat with increasing frequency as it does in DDS devices. Alternatively the inverse sinc correction can be chosen, in which case the output is flat and high. -With the program AD9854C.exe one can set and tune the frequency in CW-mode. For use as a receiver LO also IF can be given and the both possible receiving frequencies are printed on the screen. The level in Q-outputs can be varied by giving the wanted attenuation in dB. This function is done by controlling a 12b digital multiplier in the device. In this case the level decreases somewhat with increasing frequency as it does in DDS devices. Alternatively t
    2022-08-02 19:18:16下载
    积分:1
  • 16×2 LCD模块显示例程,供需要的人参考
    16×2 LCD模块显示例程,供需要的人参考-16 × 2LCD module routines for those who need it for reference
    2022-03-06 00:44:25下载
    积分:1
  • 该程序为51单片机做的频率计,可计频率可达999 HZ.
    该程序为51单片机做的频率计,可计频率可达999 HZ.-The program for 51 single-chip to do the frequency meter may include frequency up to 999 HZ.
    2022-01-26 02:26:37下载
    积分:1
  • TLC5618 D/A 输出
    TLC5618 D/A 输出-Programmable DoubleChannel12-bit DACTLC5618in D/A output
    2022-08-25 02:47:58下载
    积分:1
  • AD9852的单音频产生波形程序 加载失时钟是内部设置的
    AD9852的单音频产生波形程序 加载失时钟是内部设置的 -AD9852 single audio waveform procedures produce an internal clock to load default settings
    2023-07-10 21:20:04下载
    积分:1
  • 档案包含OLED液晶驱动,单片机模型vgg12864,LCD…
    该压缩包包含了型号为VGG12864的OLED液晶的单片机驱动程序,液晶使用说明以及字模生成软件。该工程对应单片机型号为Motorola的MC68HC908GZ32,只需在头文件中对I/O简单配置后即可使用与其他任何型号的单片机-The archive contains the model VGG12864 of OLED LCD driver, microcontroller, LCD instructions, as well as matrix generation software. The project SCM model corresponds to Motorola" s MC68HC908GZ32, just in the header file of the I/O simple configuration can be used with any other type of MCU
    2023-05-21 07:20:03下载
    积分:1
  • 步进电机控制程,加减速控制。行走步数控制
    步进电机控制程,加减速控制。行走步数控制-Stepper motor control process, acceleration and deceleration control. Control of walking a few steps
    2022-02-12 08:58:33下载
    积分:1
  • Philips单片机P89C51RD和西门子Profibus工业总线的接口程序,硬件是鼎实公司的实验板,使用的鼎实公司的总线桥....
    Philips单片机P89C51RD和西门子Profibus工业总线的接口程序,硬件是鼎实公司的实验板,使用的鼎实公司的总线桥.-Siemens Profibus and Industrial Access Bus export procedures, hardware Teijitsu board of the company, using the company"s Teijitsu Bus Bridge.
    2022-12-28 11:10:04下载
    积分:1
  • 696516资源总数
  • 106913会员总数
  • 8今日下载