-
LCD module times expected 12,864 Chinese
液晶模块12864中文次料-LCD module times expected 12,864 Chinese
- 2022-02-01 19:15:25下载
- 积分：1
-
该程序为51单片机做的频率计,可计频率可达999 HZ.
该程序为51单片机做的频率计,可计频率可达999 HZ.-The program for 51 single-chip to do the frequency meter may include frequency up to 999 HZ.
- 2022-01-26 02:26:37下载
- 积分：1
-
PIC18系列下的DS1302时钟程序 源吗哦 测试通过可以用
PIC18系列下的DS1302时钟程序 源吗哦 测试通过可以用-PIC18 series under the DS1302 clock source you Oh the test can be used
- 2022-03-19 00:28:03下载
- 积分：1
-
中国ST16C554纸条，上
st16c554的中文说明，网上下的，很不错-Chinese st16c554 note, on-line under the very good
- 2022-03-18 01:36:21下载
- 积分：1
-
max197采样程序,采用STC89C52RC单片机
max197采样程序,采用STC89C52RC单片机-MAX197 sampling procedures STC89C52RC Singlechip
- 2022-08-08 20:31:52下载
- 积分：1
-
80C52参考频率计程序，包含中断和定时器典型应用代码段
80C52参考频率计程序，包含中断和定时器典型应用代码段-Reference 80C52 Cymometer procedures, including suspension and timer typical application code segment
- 2022-08-20 13:25:43下载
- 积分：1
-
使用51单
利用51单片机来实现航标灯的控制，使用定时器来控制二极管的发光，可以模拟水上航标灯的功能，实现对过往船只的航向指引！-The use of 51 single-chip to achieve the control of aids to navigation lights, the use of timers to control the light-emitting diode, can simulate the function of water navigation lights, the achievement of passing ships on the guidelines of course!
- 2022-04-01 17:52:45下载
- 积分：1
-
单片机实现TCPIP协议的完整C源程序
TCP <
单片机实现TCPIP协议的完整C源程序
TCP RS232 的应用
分配本地用户自定义服务模式应用TCP端口号-MCU TCPIP protocol complete C source code
- 2022-02-07 01:42:51下载
- 积分：1
-
用于步进电机的驱动.可以通过输出信号来控制步进电机的转速和角度控制....
用于步进电机的驱动.可以通过输出信号来控制步进电机的转速和角度控制.-For stepper motor driver. Can output signals to control the stepper motor speed and angle control.
- 2022-07-09 00:19:55下载
- 积分：1
-
At can be given its arguments in a file. You can comment
out lines by precedin...
At can be given its arguments in a file. You can comment
out lines by preceding them with either # or -
characters. This is an easy way to temporarily disable
some commands.
The CONTINUE-command is most useful at the end of the
file. When this command is read, the file is started
again from the beginning. You can use it situations where
the machine is not shut down for the night and you want
to run some commands every day.- At can be given its arguments in a file. You can comment
out lines by preceding them with either# or-
characters. This is an easy way to temporarily disable
some commands.
The CONTINUE-command is most useful at the end of the
file. When this command is read, the file is started
again from the beginning. You can use it situations where
the machine is not shut down for the night and you want
to run some commands every day.
- 2022-02-21 09:29:04下载
- 积分：1
