-
关干高速PCB设计的设计技巧，PCB硬件开发指南。
关干高速PCB设计的设计技巧，PCB硬件开发指南。-Dry off the design of high-speed PCB design techniques, PCB hardware development guide.
- 2022-05-14 19:08:52下载
- 积分：1
-
sd card procedures, the above records the SD card reader to write in detail the...
sd卡的程序，上面记录了SD卡的详细读卡写卡方式，适合51单片机或者其他-sd card procedures, the above records the SD card reader to write in detail the way cards for 51 single-chip or other
- 2022-05-28 03:48:59下载
- 积分：1
-
这是监视器行业常见摄像头与球机通讯协议的C语言源代码
这是监视器行业常见摄像头与球机通讯协议的C语言源代码-Did视tong 器 soil shallow quickly-deteriorating jade摄像inspectors are rude与球 Lennon stabbed Services协Hu Sheng Tai Pang cavity C Tungsten measurements
- 2022-03-25 18:21:29下载
- 积分：1
-
锁定键盘的程序,程序中设定了密码正确标志,在编译软件中编译成功....
锁定键盘的程序,程序中设定了密码正确标志,在编译软件中编译成功.-keyboard lock procedures, procedures set password correct signs, the compiler software compiler success.
- 2022-03-11 18:53:50下载
- 积分：1
-
设计分为5 个模块：前轮PWM 驱动电路、后轮PWM 驱动电路、轨迹探测
模块、障碍物探测模块、光源探测模块。前轮PWM 驱动电路用于转向控制；后
轮P...
设计分为5 个模块：前轮PWM 驱动电路、后轮PWM 驱动电路、轨迹探测
模块、障碍物探测模块、光源探测模块。前轮PWM 驱动电路用于转向控制；后
轮PWM 驱动电路用于方向和速度控制；-Design is divided into five modules: front-wheel drive PWM circuit, rear-wheel drive PWM circuit, the track detection module, obstacle detection module, detecting the light source module. PWM drive circuit for front-wheel steering control rear-wheel drive circuit for PWM direction and speed control
- 2023-02-09 00:25:04下载
- 积分：1
-
控制ADLTC1407转换器工作，实现模数转换功能
控制ADLTC1407转换器工作，实现模数转换功能-AD LTC1407
- 2022-08-15 12:30:19下载
- 积分：1
-
C8051f020 MCU Flash memory AD45DB081
c8051f020单片机Flash存储器AD45DB081-C8051f020 MCU Flash memory AD45DB081
- 2022-01-26 17:07:29下载
- 积分：1
-
用vb写的能够查看所有系统进程和进程所加载的模块
用vb写的能够查看所有系统进程和进程所加载的模块-Using vb to write the be able to view all system processes and process modules loaded
- 2023-07-13 06:10:03下载
- 积分：1
-
单片机数据采集与传输给上位机
单片机实现数据采集并传送到上位机-MCU data acquisition and transmission to the PC
- 2023-06-21 05:00:03下载
- 积分：1
-
利用动态扫描和定时器1在数码管上显示
出从765432开始以1/10秒的速度往下递减
直至765398并保持显示此数，与此同时利
用定时器0以500...
利用动态扫描和定时器1在数码管上显示
出从765432开始以1/10秒的速度往下递减
直至765398并保持显示此数，与此同时利
用定时器0以500MS速度进行流水灯从上至
下移动，当数码管上数减到停止时，实验
板上流水灯也停止然后全部开始闪烁，3秒
后（用T0定时）流水灯全部关闭、数码管上
显示出"HELLO"。到此保持住。
设晶振频率为12MHz。-The use of dynamic scanning and Timer 1 in the digital control to show from the beginning of 765,432 to 1/10 seconds until the speed of descending down 765,398 and maintain display this number, at the same time the use of Timer 0 to 500ms the speed of light from the flowing water to Under the move, when reduced to a few digital tube stop, the experiment on-board water stop and then all the lights started to flicker, 3 seconds later (T0 regularly used) closed water lights, digital tubes show
- 2022-02-03 00:14:56下载
- 积分：1
