一个数字电压表的设计

this is visual c++ 6 project it is a Serial port excerszier software

设为停车场内只有一个可停放n辆汽车的狭长通道,且只有一个大门可供汽车进出,汽车在停车场内按车辆到达时间的先后顺序,依此由北向南排列(大门在最南端,最初到达的汽车停放在停车场的最北端),若停车场内已停满了n辆汽车,则后来的汽车只能在门外的便道上等候,一旦有汽车开走,在它之后开入的车辆必须先退出停车场为它让路,待该辆开出大门外,其它车辆再按原次序进入停车场,每辆停放在停车场在汽车在它离开停车场时必须按它停留时间-Set only a car park to park cars n the narrow channel and only one door and out of cars, cars in the carpark by the arrival of the vehicles in chronological order, and so north to south with (the southernmost tip of the door, first arrived in a car parked in the parking lot of the most North) if parking has been full of parked cars in the n, the car was only at the door waiting on the sidewalk, when the bus pulled away, after it was opened to vehicles must first withdraw from the car park to make way for it, when the big vehicles out the door, other vehicles according to the original order of entry, in each park parking in the car when it left the car park as it must stay

pic16f616红外遥控调节PWM占空比(the pic16f616 infrared remote control to adjust the PWM duty cycle)

c#语言编写。遍历磁盘所有文件夹和文件。实现资源管理器的功能。用VS2005环境开发(c# language. Traverse the disk all the folders and files. To achieve resource manager functions. Environmental development with the VS2005)

说明：  为解决实际测控系统中在控制中心的上位机和控制功能设备的下位机之间传送命令和文件的问题,在讨论VC++6.0中MSComm控件的基础上,通过制定通信协议、给命令和文件加入标识构成包进行传送,从而正确地区分了命令和文件.实验表明,基于该通信协议,可以成功地传送命令和多类型文件. (To address the actual measurement and control system in the Control Center PC and control functions of equipment under the digital transmission between orders and documents, in discussing the VC++ 6.0 in MSComm control on the basis of the communication protocol through the development to the orders and adding logo files constitute a packet transmitted, thereby correct distinction between the orders and documents. The experimental results show that based on the communication protocol, you can successfully send a command and multi-type documents.)

说明：  和outlook界面类似的一个界面例程,vc++mfc实现(, vc mfc implementation of an Interface routine similar to the outlook Interface)

ATAPI 接口的C语言实现。包括说明文档(the c code for ATAPI driver. document included)

传感器是一种检测装置，能感受到被测量的信息，并能将感受到的信息，按一定规律变换成为电信号或其他所需形式的信息输出，以满足信息的传输、处理、存储、显示、记录和控制等要求(Sensor is a kind of detection device, which can sense the measured information and transform it into electrical signal or other required information output according to certain rules to meet the requirements of information transmission, processing, storage, display, recording and control.)

一个很好的图像处理程序(a good image-processing program)

nordic 2.4G RF transceiver nRF24z01 firmware source code.(nordic 2.4G RF transceiver nRF24z01 firmw are source code.)