-
cc2420发程序,用来实现发射功能,单片机采用msp430!
cc2420发程序,用来实现发射功能,单片机采用msp430!-cc2420 the procedures used to achieve launch function, using SCM Controller!
- 2023-08-01 04:10:02下载
- 积分:1
-
430AD实验并有液晶驱动资料,已实验通过,请放心下载
430AD实验并有液晶驱动资料,已实验通过,请放心下载-Experimental 430AD and LCD driver information, has the experiment through, please be assured Download
- 2022-04-28 07:13:35下载
- 积分:1
-
凌阳单片机驱动12864液晶,控制器ST7290
凌阳单片机驱动12864液晶,控制器ST7290-Sunplus 12864 single-chip LCD driver, controller ST7290
- 2022-03-02 14:47:50下载
- 积分:1
-
本文件是ATMEGA16A的使用说明,内附该单片机内部各个资源的C代码和汇编代码...
本文件是ATMEGA16A的使用说明,内附该单片机内部各个资源的C代码和汇编代码-This document is the use of ATMEGA16A that the single chip containing all the resources within the C code and assembly code
- 2023-02-16 15:10:05下载
- 积分:1
-
此程序为调试通过的程序,有键盘输入和LED输出的功能
此程序为调试通过的程序,有键盘输入和LED输出的功能-this procedure through the debugging process, LED keyboard input and output functions
- 2022-08-14 03:05:14下载
- 积分:1
-
keilc+ proteus light parallel port design of experiments requirements: master th...
keilc + proteus
并行口设计指示灯实验
要求:掌握80C51单片机输入输出接口使用方法
学会开关量输入输出控制的接口技术及编程方法
实验题目:8个发光二极管D1~D8分别接在单片机P1.0-P1.7端口上,一个开关接在P3.0上。要求输出端口输出 “0”时,发光二极管亮。开关闭合时,开始按P1.0-P1.1-...-P1.7的顺序依次点亮LED,再按 P1.7-P1.6 -...-P1.0的顺序点亮LED,重复循环。开关断开时,立刻停止点亮指示灯。-keilc+ proteus light parallel port design of experiments requirements: master the 80C51 microcontroller input and output interfaces Society of switch to use the amount of input and output control interface technology and programming methods Experimental subjects: eight light-emitting diodes D1 ~ D8, respectively connected to the MCU P1.0-P1 .7 port on a switch connected to the P3.0 on. Requested output port output " 0" , the light-emitting diode light. Is closed, to embark on the P1.0-P1.1-...- P1.7 in the order light LED, and then P1.7-P1.6-...- P1.0 order light LED Repeat cycle. Switch off when the stop light indicator.
- 2022-11-16 18:10:03下载
- 积分:1
-
详细介绍了摄像机标定的原理
详细介绍了LCD相机标定的原理-Described in detail the principles of camera calibration LCD
- 2022-03-14 07:08:08下载
- 积分:1
-
大型商用电磁炉的源码程序,通过此程序可实现电磁炉的各种功能...
大型商用电磁炉的源码程序,通过此程序可实现电磁炉的各种功能-Large commercial induction cooker of the source process, this process can be achieved through a variety of functional induction cooker
- 2022-07-02 03:16:02下载
- 积分:1
-
本程序可以利用74164串入并出芯片在七段共阴数码管上依次点亮0至9十个数字..
PA0....数据
PA1.....CP
PA2.....是位选...
本程序可以利用74164串入并出芯片在七段共阴数码管上依次点亮0至9十个数字..
PA0....数据
PA1.....CP
PA2.....是位选
在ATMEGA644P上调试通过-This procedure can be used to string 74,164 and a total of a chip in the seventh followed by vaginal digital tube light figures 0-9 10 .. PA0 .... data PA1 ..... CP PA2 ..... is selected through ATMEGA644P debugging
- 2022-02-13 12:35:35下载
- 积分:1
-
基于AT89C51和DS18B20的最简温度测量系统
温度检测的传统方法是使用诸如热电偶、热电阻、半导体PN结之 类的模拟温度传感器。信号经取样、放大后通过...
基于AT89C51和DS18B20的最简温度测量系统
温度检测的传统方法是使用诸如热电偶、热电阻、半导体PN结之 类的模拟温度传感器。信号经取样、放大后通过模数转换,再交自单片机处理。被测温度信号从温敏元件到单片机,-Based on AT89C51 and Jane DS18B20 most temperature measurement system temperature detection is the use of traditional methods such as thermocouples, thermal resistors, semiconductor PN junction, such as analog temperature sensor. Signal sampling, amplified through the analog-digital conversion, and then deal with pay since the single-chip microcomputer. The measured temperature signal from the thermo-sensitive components to the microcontroller,
- 2022-03-13 06:30:32下载
- 积分:1