登录
首页 » SCM » 电子称 AD中文说明

电子称 AD中文说明

于 2022-04-25 发布 文件大小:595.04 kB
0 137
下载积分: 2 下载次数: 1

代码说明:

电子称 AD中文说明-dianzicheng yingwenshuoming

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • 鱼缸控制器带声光功能,可控温、加氧,人体感应音乐播放。...
    鱼缸控制器带声光功能,可控温、加氧,人体感应音乐播放。-Fish tank with sound and light controller features temperature control, add oxygen, the body sensors music player.
    2023-06-24 06:40:04下载
    积分:1
  • 高速PCB设计资料,很好的东西,推荐下载
    高速PCB设计资料,很好的东西,推荐下载-High-speed PCB design data, very good things, recommended download
    2022-04-22 10:34:10下载
    积分:1
  • SCM CPU timing
    单片机CPU时序-SCM CPU timing
    2022-01-24 08:59:06下载
    积分:1
  • IC Card operating software : AT88SCl604 chip mode of operation there are five. T...
    IC卡操作软件:AT88SCl604芯片的操作模式有五种。它们是通过配PGM、RST、CLK等引脚信号及内部地址计数器(IAC)的状态组合来实现。 (1) 芯片复位操作: AT88SCl604有两种复位方式:上电复位和控制复位。 上电复位: 上电复位是当芯片加电时的最初状态。上电复位属于芯片 内部复位。它将使芯片内部所有的隐含标志复位到"0"状态。并使地址计数器复位到0位。 控制复位: 当CLK为低时,在RST脚上的一个下降沿将便芯片产生复位操作。 控制复位是将地址计数器复位到0位,而不影响任何内部标志的状态。-IC Card operating software : AT88SCl604 chip mode of operation there are five. They are allocated by PGM, RST, etc. pin CLK signal and the internal address counter (IAC) portfolio of the state is to be achieved. (1) chip reset operation : reduction AT88SCl604 two ways : power-on reset and reset control. Power-on reset : power-on reset when the chip is in power at the initial state. Power-on reset the internal chip is reset. It will enable all internal chip implied signs reset to "0" state. Make address counter reset to 0. Reset control : When the CLK for the low, the RST feet of a falling edge chips will have to reset operation. Reset control is to address counter reset to 0, without prejudice to any signs of internal sta
    2022-05-28 08:23:00下载
    积分:1
  • PC 通过串口工具在发送节点A 端输入想要发送的数据,点击发送,在接收节点B 端 PC 上的串口工具上,可以看到节点B 收到的内容。如要发送10 个字节内容...
    PC 通过串口工具在发送节点A 端输入想要发送的数据,点击发送,在接收节点B 端 PC 上的串口工具上,可以看到节点B 收到的内容。如要发送10 个字节内容为11 22 33 44 55 66 77 88 99 AA 的数据/时,在发送节点A 端的串口工具上输入 0A 11 22 33 44 55 66 77 88 99AA,其中0A 代表要发送数据的长度,以16 进制表示。在接收节点B 端的串口工具上就可以收到相应的数据。-PC through the serial port tool sending node A wants to send data from client input, click on send, at the receiving node B-side on a PC serial port tools, you can see the node B received. If you want to send 10 bytes of content 11 22 33 44 55 66 77 88 99 AA of the data/pm at the sending node A on the input side of serial port tools 0A 11 22 33 44 55 66 77 88 99AA, in which you want to send on behalf 0A the data length to 16 hexadecimal said. Node B at the receiving end of the tool on the serial port can receive the corresponding data.
    2022-04-24 02:24:33下载
    积分:1
  • 24c02
    24c02-24c512 c51驱动-24c02-driven 24c512 decoder
    2023-07-17 22:25:03下载
    积分:1
  • AT24C02的应用例程,进行eeprom和I2C的应用设计
    AT24C02的应用例程,进行eeprom和I2C的应用设计-AT24C02 Application routines for I2C EEPROM and Application Design
    2023-05-15 16:20:04下载
    积分:1
  • AVR(ATMEL)+ VS1003(VLSI)Mp3播放器
    AVR(Atmel)+VS1003(VLSI) Easy MP3 Player
    2023-06-29 09:10:04下载
    积分:1
  • 该源码采用标准c编写,使用SPI方式访问SD卡。
    该源码采用标准c编写,使用SPI方式访问SD卡。-c prepared using standard, the use of SPI mode visit the SD Card.
    2022-05-31 14:35:12下载
    积分:1
  • 采用dspic30f2010的变频器核心驱动程序,程序可以实现正转/反转,频率设定,保护等...
    采用dspic30f2010的变频器核心驱动程序,程序可以实现正转/反转,频率设定,保护等-the inverter used dspic30f2010 core drivers, procedures can be achieved is to/inversion, frequency creation, protection
    2022-02-01 21:49:59下载
    积分:1
  • 696516资源总数
  • 106409会员总数
  • 8今日下载