登录
首页 » Matlab » 好用的MeanShift算法源码

好用的MeanShift算法源码

于 2022-04-27 发布 文件大小:3.75 kB
0 86
下载积分: 2 下载次数: 1

代码说明:

构成不同频率的调制信号,ldpc码的编解码实现,matlab程序运行时导入数据文件作为输入参数,给出接收信号眼图及系统仿真误码率,搭建OFDM通信系统的框架,用MATLAB实现动态聚类或迭代自组织数据分析。

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • videotime
    用matlab打开视频,并测试处理30帧图像需要的时间(Using matlab to open the video, and test the processing time of 30 images)
    2012-06-18 16:24:47下载
    积分:1
  • Radar-signal-processing
    雷达信号的基本模型,高斯分布,几何分布,求信号的概率分布,概率密度函数,功率谱函数,自相关函数等等(The basic model of the radar signal, Gaussian distribution, geometric distribution, the probability distribution for the signal, probability density function, power spectrum, the autocorrelation function, and so)
    2013-08-27 11:10:48下载
    积分:1
  • System-Identifiation
    Predator-Prey Model With GA.
    2015-03-27 18:43:18下载
    积分:1
  • tabu-search-matlab
    求解VRP 问题的智能算法 禁忌搜索算法MATLAB源代码(tabu-search MATLAB code of VRP )
    2015-07-02 19:53:02下载
    积分:1
  • 程序
    多因子选股模型有效因子检验matlab算法实现(Multi-factor stock selection model effective factor test matlab algorithm implementation.)
    2021-01-12 15:28:48下载
    积分:1
  • 13004499
    Matlab image inpainting using deep learning
    2020-06-22 13:20:02下载
    积分:1
  • 项目4
    说明:  任务:设计一个4×2.5Gbit/s 长距离光纤传输系统,并利用OptiSystem 仿真验证。 要求: 1.采用波分复用技术,波长设置以100GHz 为间隔,频率分别为193.1THz、193.2THz、193.3THz、193.4THz,每个波长传输速率为2.5Gbit/s(NRZ),传输距离为300km。采用常规光纤,光纤损耗系数为0.25dB/km。 2.单通道光发送机最大输出功率为0dBm,光接收机的接收光功率不低于-26dBm,过载点为-10dBm。 3.可以采用EDFA 作为线路放大器,其中EDFA 的输入功率限制在-18~2dBm,最大输出功率20dBm,增益范围为13~25dB,噪声指数4.0dB。(Task: Design a 4 x 2.5 Gbit/s long-distance optical fiber transmission system, and use OptiSystem simulation to verify. Requirement: 1. Using wavelength division multiplexing technology, the wavelength is set at 100GHz intervals, with frequencies of 193.1 THz, 193.2 THz, 193.3 THz and 193.4 THz, respectively. The transmission rate of each wavelength is 2.5 Gbit/s (NRZ), and the transmission distance is 300 km. The loss coefficient of conventional optical fibers is 0.25dB/km. 2. The maximum output power of a single-channel optical transmitter is 0 dBm, and the receiving power of an optical receiver is not less than -26 dBm, and the overload point is -10 dBm. 3. EDFA can be used as line amplifier, where the input power of EDFA is limited to - 18-2dBm, the maximum output power is 20dBm, the gain range is 13-25dB, and the noise index is 4.0dB.)
    2019-05-13 09:39:41下载
    积分:1
  • yangshiganshedemoli
    这是一个用MATLAB编的一个杨氏干涉的模拟程序,很有意思,和大家分享(This is a MATLAB an addendum to the Young's interference in the simulation program, very interesting, and we share)
    2007-05-05 10:57:37下载
    积分:1
  • LTE_Downlink[1]
    维也纳大学,LTE-A下行链路matlab链路级仿真程序。(University of Vienna, LTE-A downlink link level simulation matlab program.)
    2021-02-02 19:39:59下载
    积分:1
  • 分数阶Fourier变换信号处理
    说明:  分数阶滤波,FRFT自适应滤波,以及其实例。 附有相对应的数据可用给的程序做处理。(Fractional order filtering, FRFT adaptive filtering, and its example. The corresponding data are attached, which can be processed by the program.)
    2020-10-29 21:23:46下载
    积分:1
  • 696518资源总数
  • 106227会员总数
  • 11今日下载