-
C++的单片机编程
C++的单片机编程-C++ Microcontroller programming
- 2022-08-20 09:00:12下载
- 积分：1
-
80C52参考频率计程序，包含中断和定时器典型应用代码段
80C52参考频率计程序，包含中断和定时器典型应用代码段-80C52 reference Cymometer procedures, including suspension and timer typical application code segment
- 2022-03-01 09:31:32下载
- 积分：1
-
采用ADC0809采集数据，并通过串口上传到上位机，采用C语言编写，简单易懂...
采用ADC0809采集数据，并通过串口上传到上位机，采用C语言编写，简单易懂-using data acquisition, and through serial upload it to the PC using C language. easily understood
- 2022-07-28 05:38:32下载
- 积分：1
-
c8051f021单片机资料
c8051f021单片机资料-c8051f021
- 2022-01-25 15:25:10下载
- 积分：1
-
搞电子的人经常用的一些仪器的使用说明书（示波器，信号发生器、电源）...
搞电子的人经常用的一些仪器的使用说明书（示波器，信号发生器、电源）-People engage in electronic equipment, often with the use of the specification (oscilloscopes, signal generators, power supply)
- 2023-02-03 17:55:04下载
- 积分：1
-
MCS
MCS-51单片机有5个中断源，其中两个是由-INT0、-INT1引脚输入的外部中断源；另外三个是内部中断源即由T0、T1的溢出引起中断和串行口发送完一个字节或接收到一个字节数据引起中断。触发外部中断有两种方式，即下降沿引起中断或低电平引起中断。当编程TCON中的ITi（i=0、1）为1时，则引起触发的方式为边沿触发方式，反之(ITi=0)为低电平触发方式。每个中断源的中断请求能否得到响应要受两级“开关”的控制，即一个总“开关”-MCS-51 single-chip has five interrupt sources, two of which are by-INT0,-INT1 pin input external interrupt source the other three internal interrupt sources from the T0, T1 overflow caused by the disruption and serial port sending or receiving end of a byte to a byte of data caused by interruption. Triggered external interrupt has two modes, namely, falling edge or low-level disruption caused disruption caused. When programming TCON in ITi (i = 0,1) for the 1:00 has been the subject of a way to trigger the way to the edge of the trigger, on the contrary (ITi = 0) for low-level trigger mode. Each interrupt source interrupt request can be subject to levels in response to
- 2023-07-06 00:00:03下载
- 积分：1
-
A stepping motor driver program written by Keil C51.
用Keil C51写的步进电机驱动程序。-A stepping motor driver program written by Keil C51.
- 2022-01-31 20:35:25下载
- 积分：1
-
AVR s AVR
AVR s AVR-CDC ，form OURAVR,COM-AVR s AVR-CDC, form OURAVR, COM
- 2022-02-01 22:15:45下载
- 积分：1
-
* 功能：LPC2100的IAP功能测试。
* 说明：调用IAP服务程序，完成FLASH编程操作。
* 将paramout添加到Watch窗口，观察返回...
* 功能：LPC2100的IAP功能测试。
* 说明：调用IAP服务程序，完成FLASH编程操作。
* 将paramout添加到Watch窗口，观察返回值。-* Function: LPC2100 the IAP function test.* Description: Call IAP service program, complete the FLASH programming operation.* Will paramout added to the Watch window to observe the return value.
- 2023-09-04 10:20:03下载
- 积分：1
-
the procedures provided ADuC812 SCM ad/da testing procedures.
本程序提供了ADuC812单片机的ad/da测试程序。-the procedures provided ADuC812 SCM ad/da testing procedures.
- 2022-03-21 22:01:21下载
- 积分：1
