登录
首页 » 嵌入式芯片 » ARM7―LPC2124―LCD开发实例 基于Keil uVision3源码开发再进行Proteus 7 联合对ARM7―LPC2124―I2C硬件电路仿真...

ARM7―LPC2124―LCD开发实例 基于Keil uVision3源码开发再进行Proteus 7 联合对ARM7―LPC2124―I2C硬件电路仿真...

于 2022-05-16 发布 文件大小:199.87 kB
0 121
下载积分: 2 下载次数: 1

代码说明:

ARM7―LPC2124―LCD开发实例 基于Keil uVision3源码开发再进行Proteus 7 联合对ARM7―LPC2124―I2C硬件电路仿真-ARM7-LPC2124-LCD development examples Keil uVision3 source development based on further joint Proteus 7 on ARM7-LPC2124-I2C hardware circuit simulation

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • 完整的程控放大器菜单加控制程序, 1开始菜单 2功能选择高频低频 3选择手动调节还是自动调节4 若自动调节输放大增益值 结束页然后根据你所选择的功能进行控...
    完整的程控放大器菜单加控制程序, 1开始菜单 2功能选择高频低频 3选择手动调节还是自动调节4 若自动调节输入放大增益值 结束页然后根据你所选择的功能进行控制程控放大器-programable gain amplifier
    2022-01-28 14:36:52下载
    积分:1
  • This example program shows how to configure and use the A/D Converter of the fo...
    This example program shows how to configure and use the A/D Converter of the following microcontrollers: * Philips LPC 2114/2119/2124/2129/2131/2132/2138/2194 After configuring the A/D Converter, the program reads A/D channel 0 and outputs the converted value using the serial port. To run this program... 1. Select the Device (Project - Options for Target - Device) 2. Build the project (Project - Build Target) 3. Start the uVision Debugger 4. Open the Serial Window (View - Serial Window 1) 5. Click Run (F5) 6. Click on the Toolbox buttons to change input voltages A debug script (debug.ini) creates buttons that set different analog values in A/D channels. As the program runs, you will see the A/D input and output change. Other buttons create signals that generate sine wave or sawtooth patterns as analog inputs. µ Vision3 users may enable the built-in Logic Analyzer to view, measure and compare these input signals grap
    2022-01-31 01:19:45下载
    积分:1
  • 一个CAN总线应用的sample ,采用LPC2119处理器.
    一个CAN总线应用的sample ,采用LPC2119处理器.-CAN bus applications, a sample, using LPC2119 processor.
    2022-09-02 13:05:03下载
    积分:1
  • JTAG的驱动程序,一般都是用在相对应的ARM处理器上,这个事实用在LPC2210上面。...
    JTAG的驱动程序,一般都是用在相对应的嵌入式ARM处理器上,这个事实用在LPC2210上面。-JTAG drivers are generally used in relation to the embedded ARM processor, with the fact that the LPC2210 above.
    2022-03-10 04:15:46下载
    积分:1
  • SIM800程序
    sim800 keil4程序,传输没问题,能够传输图片数据,运行稳定
    2022-01-22 07:27:25下载
    积分:1
  • UCOSII消息队列、信号量集和软件定时器
    应用背景软件定时器,UCOSII消息队列,使用比较实用的软件编程思路,在实践中很受益,,,关键技术UCOSII消息队列 ,如果管理消息列队,如何做调度器,软件定时器等,能同时处理大量问题,,,,
    2022-06-02 02:33:31下载
    积分:1
  • ali source
    描述:将UTM坐标向量转换为纬度/经度向量的函数(WGS84)。
    2022-12-15 18:00:04下载
    积分:1
  • 基于srt
    基于srt-2算法,利用verilog实现16位定点无符号数除法器(除数、被除数均由16位整数和16位小数组成,商由32位整数和16位小数构成,余数由32位小数组成)-Based on srt-2 algorithm, using verilog to achieve 16-bit fixed-point unsigned divider (divisor, dividend by 16-bit integer and 16-bit decimal form, business from the 32-bit integer and 16-bit fractional composition, I composed a few from the 32-bit decimal)
    2022-03-19 07:07:06下载
    积分:1
  • atmel sam7a3 串口 pdc keil下成功运行 可在7a3 开发板上运行,并且带有闪灯程序...
    atmel sam7a3 串口 pdc keil下成功运行 可在7a3 开发板上运行,并且带有闪灯程序-pdc serial atmel sam7a3
    2023-05-29 12:20:02下载
    积分:1
  • fpga 健身器自行车控制器
    用fpga实现的健身器自行车控制器,有两种模式,第一种模式下,f启动,选择1模式,e确定。选择强度e确定,d开始。第二种模式下f启动,选择2模式,e确定,选择强度,e确定,输入训练时间,c清楚,e确定,d开始。最后三秒钟有led灯亮起提示。
    2022-03-22 01:20:06下载
    积分:1
  • 696518资源总数
  • 106161会员总数
  • 5今日下载