-
基于Keil C平台的源程序，是针对AT89ls52的4×4键盘扫描程序，采用查询方式进行...
基于Keil C平台的源程序，是针对AT89ls52的4×4键盘扫描程序，采用查询方式进行-Keil C based on the source platform is AT89ls52 for the 4 × 4 keyboard scanning procedures, the use of inquiries conducted
- 2023-01-02 22:45:04下载
- 积分：1
-
关于AD590的说明，包含若干应用电路图。
关于AD590的说明，包含若干应用电路图。-Note on the AD590, contains a number of applications circuit.
- 2022-03-24 22:26:07下载
- 积分：1
-
51 microcontroller programming paradigm (timer/counter software programming para...
51单片机编程范例（定时/计数器软件编程范例）-51 microcontroller programming paradigm (timer/counter software programming paradigm)
- 2023-03-10 10:50:04下载
- 积分：1
-
8279键盘单片机c语言编码，很实用哦。
8279键盘单片机c语言编码，很实用哦。-8279 keyboard Singlechip c language coding, it is practical Oh.
- 2022-02-07 20:57:07下载
- 积分：1
-
基于ATMEL Mega8的电阻测量仪，附带Proteus仿真
基于ATMEL Mega8的电阻测量仪，附带Proteus仿真-Based on ATMEL Mega8 resistance measuring instrument, with Proteus Simulation
- 2023-05-23 21:30:03下载
- 积分：1
-
< AVR C语言的应用>>第九章中的例子
用ATmega1280 在IAR Embedded Workbench IDE平台编译连接通过...
< AVR C语言的应用>>第九章中的例子
用ATmega1280 在IAR Embedded Workbench IDE平台编译连接通过的12个程序
-< > Example of the ninth chapter in the ATmega1280 with IAR Embedded Workbench IDE compiler platform to connect through the 12 procedures
- 2022-07-07 09:27:01下载
- 积分：1
-
7541数字高频头源程序，7541数字高频头源程序
7541数字高频头源程序，7541数字高频头源程序-7541 digital tuner source, 7541 the first digital high-frequency source
- 2023-06-17 20:10:03下载
- 积分：1
-
HT24 系列的EEPROM 总共8 个管脚，三个为芯片地址脚A0、A1、A2，在单片机对它进行操作时，从SDA 输入A0、A1、A2 数据和芯片外部A0、A1...
HT24 系列的EEPROM 总共8 个管脚，三个为芯片地址脚A0、A1、A2，在单片机对它进行操作时，从SDA 输入A0、A1、A2 数据和芯片外部A0、A1、A2 所接地址需一一对应。一个为芯片写保护脚WP，WP 脚接低电平时，芯片可进行读写操作；WP 脚接高时，芯片只可进行读，不可进行写。
另外两个管脚为电源脚VCC，VSS。
用单片机对HT24 系列的EEPROM 进行控制时，HT24 系列的EEPROM 的外部管脚VCC、VSS、WP、A0、A1、A2 根据需要，对应接上，SDA、SCL 接到单片机控制脚上。-HT24 Series EEPROM total of 8 pins, three pins for the chip address A0, A1, A2, in the microcontroller to operate it, from SDA input A0, A1, A2, and chip external data A0, A1, A2 of the Then one correspondence address must be in. One for the chip, write-protect pin WP, WP feet then low, the chip can be read and write operations WP pin is high then, the chip can only be read, not write. The other two pins for the power pin VCC, VSS. With the microcontroller on the HT24 Series EEPROM control when, HT24 Series EEPROM external pin VCC, VSS, WP, A0, A1, A2 according to the needs of the corresponding connected, SDA, SCL receives SCM control feet .
- 2022-01-28 04:45:28下载
- 积分：1
-
采用UART方式0与LM74通信。
用C8051f020的P0.7作片选，主机通过TXD发送时钟信号，实现同步通信,半双工.RXD
作双向数据线.用六位
采用UART方式0与LM74通信。
用C8051f020的P0.7作片选，主机通过TXD发送时钟信号，实现同步通信,半双工.RXD
作双向数据线.用六位数码管显示LM74采集的温度值-The use of UART communication mode 0 and LM74. P0.7 used for the C8051F020 chip select, host TXD sent through the clock signal, to achieve synchronous communication, half-duplex. RXD for bi-directional data line. With six digital tube display LM74 temperature collected
- 2022-06-30 14:59:56下载
- 积分：1
-
SmartGen generated with a size of 256* 8 Synchronous FIFO, and sending data thro...
用SmartGen生成一个256*8的大小同步FIFO，并通过串口发送数据初始化FIFO。然后，再通过串口返回到上位机的串口调试程序显示，确认数据是否正确。-SmartGen generated with a size of 256* 8 Synchronous FIFO, and sending data through the serial port to initialize FIFO. And then back through the serial port to the PC serial port debugger display to confirm the data is correct.
- 2022-03-03 12:50:01下载
- 积分：1
