登录
首页 » 嵌入式系统 » mega8 mcu ,iccavr ,c program ,int0 int1 ,ADC ,uart,i/o

mega8 mcu ,iccavr ,c program ,int0 int1 ,ADC ,uart,i/o

于 2022-05-27 发布 文件大小:2.85 kB
0 150
下载积分: 2 下载次数: 1

代码说明:

mega8 mcu ,iccavr ,c program ,int0 int1 ,ADC ,uart,i/o

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • 51单片机控制 1602液晶显示 读取PS2键盘程序 按键会在1602上显示所按键...
    51单片机控制 1602液晶显示 读取PS2键盘程序 按键会在1602上显示所按键-51 single-chip control 1602 to read LCD PS2 keyboard program keys will be displayed on the button 1602
    2022-02-02 12:39:39下载
    积分:1
  • D:MyData其它我的文章C51cp1_1 est.uv2 Project File Date: 04/02/2003
    D:MyData其它我的文章C51cp1_1 est.uv2 Project File Date: 04/02/2003--D:MyDataOthersMyArticlesC51cp1_1 est.uv2 Project File Date: 04/02/2003
    2022-01-26 07:18:03下载
    积分:1
  • 看门狗自动采集数据
    看门狗自动采集数据-watchdog automatic data collection
    2022-07-03 11:17:39下载
    积分:1
  • Canon IP2200 printer driver in Linux under.
    佳能打印机IP2200在Linux下的驱动。-Canon IP2200 printer driver in Linux under.
    2022-03-11 23:19:37下载
    积分:1
  • 按键扫描程序
    这是一个按键扫描程序的C代码,它可移植到任意型号的MCU或MPU中,支持短按、长按、长按累加(如调整时间加减等)、组合按键等功能。程序中实现了2*2矩阵键盘扫描,根据此例程可任意添加、减少按键。移植灵活、方便,不受芯片类型影响。
    2022-03-25 04:56:17下载
    积分:1
  • C语言循环移动与nop指令,好用的,注意头文件
    C语言循环移动与nop指令,好用的,注意头文件-C-cycle movement and nop instructions, easy-to-use, pay attention to the first document
    2022-07-03 09:16:05下载
    积分:1
  • 瑞泰
    ICETEK-OMAP3530-Mini原理图-ICETEK-OMAP3530-Mini schematic diagram
    2022-01-31 01:29:05下载
    积分:1
  • I write ARM PS2 driver, I use ordinary GPIO simulation PS2 agreement can be dire...
    我写的ARM PS2驱动程序,使用普通GPIO口模拟PS2协议,可直接驱动键盘、条码找描枪等设备,并将从键盘、条码扫描枪等输入的信号通过UART口传至PC机-I write ARM PS2 driver, I use ordinary GPIO simulation PS2 agreement can be directly driven keyboard, bar code depiction find guns and other equipment, and from the keyboard, barcode scanning guns and other input signals through UART I conveyed to PC
    2022-06-14 08:44:45下载
    积分:1
  • BLDC 矢量控制
    资源描述This application note shows how to control a permanent magnet synchronous motor (PMSM) with the sensorless field-oriented control (FOC) algorithm, using an ARM® Cortex®-M0-based PSoC 4 device. The FOC algorithm is frequently used in motor control applications because it allows motors to operate with less noise and more stable torque output than other algorithms. Sensorless FOC adds the advantage of reducing the cost due to the absence of rotor position sensors. Sensorless FOC is used in many applications including consumer (air conditioner, refrigerator), industrial (blower, pump), and commercial (elevator, escalator) products.
    2022-09-27 21:15:03下载
    积分:1
  • 148个verilog hdl小程序(有很多testbench)――.
    148个verilog hdl小程序(有很多testbench)――.-148 Verilog HDL small programs (many testbench) from Part
    2022-07-15 11:59:58下载
    积分:1
  • 696518资源总数
  • 106148会员总数
  • 10今日下载