-
CAN Driver in Keil C
CAN Driver in Keil C
- 2022-07-11 05:32:05下载
- 积分：1
-
这是一篇关于嵌入式系统的LCD液晶驱动程序的资料及源程序
这是一篇关于嵌入式系统的LCD液晶驱动程序的资料及源程序-This is an embedded system on the LCD driver and source of information
- 2022-01-21 02:33:35下载
- 积分：1
-
c51primer
c51primer
- 2022-08-15 00:28:47下载
- 积分：1
-
51单片机指令集和汇总。解压即可用
51单片机指令集和汇总。解压即可用-51 microcontroller instruction set and summary. Decompression can be used
- 2022-08-18 20:04:53下载
- 积分：1
-
With regard to the production of IC card relevant information, from easy to diff...
关于IC卡的制作的相关资料，从易道难，都是花钱买的难得的资料。-With regard to the production of IC card relevant information, from easy to difficult Road, are spending money to buy a rare information.
- 2022-02-21 13:34:32下载
- 积分：1
-
介绍基于液晶T6963C控制器的ARM程序实现
介绍基于液晶T6963C控制器的ARM程序实现-Introduction T6963C LCD Controller Based on ARM program
- 2022-03-11 06:41:06下载
- 积分：1
-
122*32 点阵 st7920 lcd中英文显示 串行驱动程序
122*32 点阵 st7920 lcd中英文显示 串行驱动程序-122* 32 dot matrix display in both Chinese and English st7920 lcd serial driver
- 2023-05-10 21:35:03下载
- 积分：1
-
实用的PIC单片机的单相双向电能芯片5460校准程序。
实用的PIC单片机的单相双向电能芯片5460校准程序。-PIC MCU practical single-phase bi-directional power 5460 chip calibration procedure.
- 2022-03-21 00:24:05下载
- 积分：1
-
C51写的普通拼音输入法源程序。编译环境：Keil C 6.14。给广大的51爱好者学习交流使用。...
C51写的普通拼音输入法源程序。编译环境：Keil C 6.14。给广大的51爱好者学习交流使用。-C51 Writing Pinyin input method common source. Compiler Environment: Keil C 6.14. To the vast number of fans 51 communicate using the study.
- 2023-05-27 02:05:03下载
- 积分：1
-
With the program AD9854C.exe one can set and tune the frequency in CW
With the program AD9854C.exe one can set and tune the frequency in CW-mode. For use as a receiver LO also IF can be given and the both possible receiving frequencies are printed on the screen. The level in Q-outputs can be varied by giving the wanted attenuation in dB. This function is done by controlling a 12b digital multiplier in the device. In this case the level decreases somewhat with increasing frequency as it does in DDS devices. Alternatively the inverse sinc correction can be chosen, in which case the output is flat and high. -With the program AD9854C.exe one can set and tune the frequency in CW-mode. For use as a receiver LO also IF can be given and the both possible receiving frequencies are printed on the screen. The level in Q-outputs can be varied by giving the wanted attenuation in dB. This function is done by controlling a 12b digital multiplier in the device. In this case the level decreases somewhat with increasing frequency as it does in DDS devices. Alternatively t
- 2022-08-02 19:18:16下载
- 积分：1
