-
基于msp430的nrf24l01的c语言程序
基于msp430的nrf24l01的c语言程序-Msp430-based c-language program of nrf24l01
- 2022-02-01 09:43:42下载
- 积分：1
-
单片机
用单片机播放音乐的源码并提供相应的音乐制作工具 -MCU-source music player and music production provided by the corresponding instrument
- 2022-05-13 06:24:57下载
- 积分：1
-
MOXA 串口驱动编程
MOXA 串口驱动编程-MOXA serial-driven programming
- 2022-06-17 10:43:22下载
- 积分：1
-
C8051F020 prepared with RA8803 LCD controller 320,240 procedures
用C8051F020编写的RA8803控制器320240液晶程序-C8051F020 prepared with RA8803 LCD controller 320,240 procedures
- 2022-02-05 02:17:23下载
- 积分：1
-
Verilog realize the DDS sine wave signal generator and frequency measurement mod...
Verilog实现的DDS正弦信号发生器和测频测相模块，DDS模块可产生两路频率和相位差均可预置调整的值正弦波，频率范围为20Hz-5MHz，相位范围为0°-359°，测量的数据通过引脚传输给单片机，单片机进行计算和显示。-Verilog realize the DDS sine wave signal generator and frequency measurement module test phase, DDS module can generate both frequency and phase difference can be preset to adjust the value of sine wave, frequency range of 20Hz-5MHz, phase range of 0 °-359 ° , measurement data and transmit them to the single-chip pin, single-chip microcomputer to calculate and display.
- 2022-04-02 09:35:43下载
- 积分：1
-
第二近轴光的实际参数.cpp
近轴光线计算
第二近轴光的实际参数.cpp
近轴光线计算-The second shaft of light near the actual parameters. Cpp
- 2022-05-09 04:25:47下载
- 积分：1
-
keil c 代码 用于usb
keil c 代码 用于usb-These are keil c source code and can be applied in usb
- 2022-10-23 01:50:03下载
- 积分：1
-
单片机模拟串行通讯程序at89c2051串口,经KEIL测试OK。
单片机模拟串行通讯程序at89c2051串口,经KEIL测试OK。-microcontroller simulation serial communication program at89c2051 serial, KEIL tests OK.
- 2022-11-13 04:10:03下载
- 积分：1
-
这个程序是控制2401模块一直发送字节，和上一次的可以配合使用，实现发射接收并且上传到电脑串口...
这个程序是控制2401模块一直发送字节，和上一次的可以配合使用，实现发射接收并且上传到电脑串口-This procedure is to control module has been sent 2401-byte, and the last can be used in conjunction to achieve the launch reception and uploaded to the computer serial port
- 2022-07-01 04:10:57下载
- 积分：1
-
此程序为自行车计附带产品．可以计里程，计速度．清零等功能．采用霍尔传感器传输信号，单片机采用中断扫描．然后用数组的形式在LED上显示．...
此程序为自行车计附带产品．可以计里程，计速度．清零等功能．采用霍尔传感器传输信号，单片机采用中断扫描．然后用数组的形式在LED上显示．-procedure for bicycles or spin-off products. Total mileage can be up speed. Reset function. Hall sensor used for signal transmission interrupt SCM scan. Then in the form of an array of LED show.
- 2023-06-19 12:15:02下载
- 积分：1
