-
UART code
UART code which tells the function and provide a lab for UART-UART code
- 2023-02-19 21:35:03下载
- 积分：1
-
串口波特率设置小软件
串口波特率设置小软件-serial port baud rate set small software
- 2023-06-05 12:00:04下载
- 积分：1
-
这个串口通信侧重于界面的编辑和数据的处理，做数据库的可以...
这个串口通信侧重于界面的编辑和数据的处理，做数据库的可以-the serial communication interface focused on the editing and processing of data, so the database can s
- 2022-11-01 09:30:03下载
- 积分：1
-
非常好用的串口编程工具 for delphi 7.0
非常好用的串口编程工具 for delphi 7.0-very user-friendly programming tools for Serial delphi 7.0
- 2022-11-24 01:00:04下载
- 积分：1
-
PLC串口编程，通过RS232和RS485通讯…
PLC串口编程,通过RS232和RS485与上位机通讯.-PLC serial port programming, through the RS232 and RS485 communication with the host computer.
- 2022-02-02 14:04:36下载
- 积分：1
-
随着视窗98的推出，越来越多的计算机用户都习惯于使用无线网络…
随着Windows98的推出，越来越多的微机用户已习惯于Windows操作系统。不过Windows应用软件的开发对于一般工程技术领域的技术人员来说并非易事，然而使用微软的VisualBasic6.0（简称VB6）来开发这些方面的Windows应用软件就十分方便，编程工作量相对较小，只需进行主要应用功能的编程和少量界面控制的编程。本文介绍利用VB6串行通信编程的方法对采用了RS-232接口的仪器,进行串行通信的计算机测控软件开发和实现仪器功能和指标的验收。-With the launch of Windows 98, more and more computer users are accustomed to Windows. But Windows application software development for the general area of engineering and technology and technical personnel is not easy, but to use Microsoft Visual Basic 6.0 (VB6) to the development of these applications on Windows is very convenient, programming workload is relatively small, only major applications programming a small amount of control and interface programming. This paper describes the use of VB6 serial communication programming method used to the RS-232 devices, serial communication control computer software development and the achievement of equipment functions and targets of acceptance.
- 2022-06-27 15:20:46下载
- 积分：1
-
C language library DOS version of the communication process to support 115200 ba...
C语言通讯程序库DOS版,支持10个115200波特率的通讯口-C language library DOS version of the communication process to support 115200 baud rate of 10 communications port
- 2022-03-06 10:59:36下载
- 积分：1
-
本程序是i2c总线读写一个字节的程序。在写过程序中，不一定非要检测i2c的应答位，可以直接延时过去就行，但是在读过程中必须给应答信号，读完发停止位，一定确认所发...
本程序是i2c总线读写一个字节的程序。在写过程序中，不一定非要检测i2c的应答位，可以直接延时过去就行，但是在读过程中必须给应答信号，读完发停止位，一定确认所发的信号都发上了。否则在连续地址读的过程中可能不会出错，但是在随机度过程中就会出错，我的程序就是在给停止信号时没有给上，24cxx一直在输出数据，结果读出错。找着问题后我的程序只加入了一条命令便完全正常。-i2c bus read and write a byte procedures. The written procedure, not necessarily require the detection i2c-response, and can directly past trip delay, but the process must be read to the response signal, stopped at reading, we recognize the signals are on the fat. Otherwise, the address read for the course could not go wrong, but the randomness of the process would be a mistake, I was in the process to stop for no signal, 24cxx in output data, read errors. I discovered the problem after the procedure just joined the order of a completely normal.
- 2022-02-02 10:09:18下载
- 积分：1
-
该程序实现了串口之间的相互通信，是异步串口通信，串口编成程序...
该程序实现了串口之间的相互通信，是异步串口通信，串口编成程序-Implementation of the procedures between the serial communications, serial communication is asynchronous, the classic experimental procedures for computer networks
- 2022-01-31 15:18:27下载
- 积分：1
-
CAN总线传输，示例代码,利用VC++编写
CAN总线传输，示例代码,利用VC++编写-CAN transmission, sample code, prepared VC
- 2022-02-03 11:46:47下载
- 积分：1
