登录
首页 » 嵌入式系统 » C51单片机的外围设备,测试程序的源代码,包括串口…

C51单片机的外围设备,测试程序的源代码,包括串口…

于 2022-08-02 发布 文件大小:22.41 kB
0 151
下载积分: 2 下载次数: 1

代码说明:

C51 单片机外围设备测试程序源码,包括Led 键盘 蜂鸣器 串口 等-C51 microcontroller peripherals, test program source code, including the serial port, etc. Led keypad buzzer

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • RTOS system, a five internal organs, though small, full
    RTOS系统,一个五脏虽小,功能集全的小系统,用来熟悉系统设计是不错的选择-RTOS system, a five internal organs, though small, full-feature set of small systems, familiar with the system design used is a good choice
    2022-08-15 00:01:30下载
    积分:1
  • 使用 xor 的计时器
    闪烁指示灯会发生与定期使用 xor 函数的代码。也可以通过 xor"ing P1.0 内部软件循环切换 P1.0。
    2023-09-05 05:45:02下载
    积分:1
  • HART协议由Rosemount公司也开
    HART协议由Rosemount公司开发且已向每个使用者开放HART协议采用标准的Bell 202频移键控信号以1200波特通信以低电平加载于4mA~20mA模拟信号上,由于载波信号的平均值为零所以它对模拟信号没有影响。-HART agreement develops by Rosemount Corporation also opened the HART agreement to each user to use the standard the Bell 202 frequency-shift keying signal increase by 1,200 bauds correspondences by the low level on the 4mA~20mA simulated signal, because intelligence signal mean value for zero therefore it has not affected to the simulated signal.
    2022-04-18 13:55:34下载
    积分:1
  • u
    u-boot.bin是使用JTAG转换板来烧写到AT2440EVB开发板上Nand flash(K9F1208)中-u-boot.bin is to use the JTAG programmer to the conversion plate to AT2440EVB development board Nand flash (K9F1208) in
    2023-06-16 20:40:06下载
    积分:1
  • 中国电波钟BPC解码程序
    中国电波钟BPC解码程序,适用精确及时的单片机和设备适用。中国电波钟BPC解码程序,适用精确及时的单片机和设备适用。中国电波钟BPC解码程序,适用精确及时的单片机和设备适用。中国电波钟BPC解码程序,适用精确及时的单片机和设备适用。
    2022-07-02 06:11:43下载
    积分:1
  • 44B0测试44B0测试44B0测试44B0测试
    44B0 test 44B0 test 44B0 test-44B0 Test 44B0 test 44B0 test 44B0 test
    2022-02-07 05:36:48下载
    积分:1
  • 2x3 Keypad libraries for CCS PIC
    2x3 Keypad libraries for CCS PIC-C users
    2022-08-13 20:39:40下载
    积分:1
  • 1768 CAN IAP升级
    CAN IAP 例程使用两块宝马开发板进行实验,分为“CAN IAP 编程板”与“CAN IAP 接收板” , 将编程板(ID=0x01)与接收板 (ID=0x02) 的 CAN1进行连接 (CAN1L 对 CAN1L, CAN1H  对 CAN1H) ,波特率为500K, 编程板通过读取板上SD卡内的app.bin文件然后传输给接收板, 每次传送1024 字节,然后等待接收板发送“CONTINUE”信号继续发送下一个1K数据, 直到发送完成,发送“UPDATAOK”通知接收板发送完成。
    2022-01-25 16:56:57下载
    积分:1
  • F320 MMC数据记录器
    F320 mmc data logger
    2022-03-15 14:14:06下载
    积分:1
  • national standards
    国家标准――电力线载波系统设计导则-national standards-- Power Line Carrier System Design Guide
    2023-02-09 18:00:03下载
    积分:1
  • 696518资源总数
  • 106140会员总数
  • 8今日下载