登录
首页 » SCM » an bunch of computer parallel port data transfer code programmed with C

an bunch of computer parallel port data transfer code programmed with C

于 2022-08-15 发布 文件大小:7.37 kB
0 151
下载积分: 2 下载次数: 1

代码说明:

一个C语言编写的单片机并口数据发送代码-an bunch of computer parallel port data transfer code programmed with C

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • PS2 读取键盘数具,非常好的一个软件PCB
    PS2 读取键盘数具,非常好的一个软件PCB-PS2 keyboard to read a few, a very good software, PCB
    2022-03-24 22:33:17下载
    积分:1
  • 一个很好的模拟单
    一个用于单片机仿真的好软件版。不需要花钱买仿真板,直接在电脑上用这个软件连接实物图就可以了。是电子设计的必备软件。里面还有教程!-A good simulation for the single-chip version of the software. The simulation does not need to spend money to buy plates, directly on your computer to use this software to connect the physical map on it. Electronic design is an essential software. There are tutorials there!
    2022-03-22 20:38:36下载
    积分:1
  • 单片机键盘控制程序模板 单片机键盘控制程序模板
    单片机键盘控制程序模板 单片机键盘控制程序模板-Keyboard control procedures Singlechip Singlechip keyboard template template control procedures
    2022-05-21 23:02:47下载
    积分:1
  • pic 16f87x pic 16f87x
    pic 16f87x pic 16f87x
    2022-03-25 03:24:09下载
    积分:1
  • 模拟交通灯,并带有数字显示的程序。初始时全为红灯,显示“HELLO”字样。然后交通灯以“红绿、红黄、绿红、黄红”四种状态做循环,而且黄灯会闪烁,每种状态都带有到...
    模拟交通灯,并带有数字显示的程序。初始时全为红灯,显示“HELLO”字样。然后交通灯以“红绿、红黄、绿红、黄红”四种状态做循环,而且黄灯会闪烁,每种状态都带有到数记时。当按下P3_2时,变成“红红”状态,并显示“STOP”字样! -simulated traffic lights and figures with the procedure. When all of the initial red, shows that the "hello" words. Then traffic lights to the "black, red and yellow, green, red, yellow red" state to do four cycle, but the yellow light flashes, each state will have a few to remember when. When pressed P3_2, into a "red" state, and shows that the "STOP" word!
    2022-01-26 03:16:31下载
    积分:1
  • 十五路遥控开关控制器 本程序为接受程序根据此程序可增加遥控路数...
    十五路遥控开关控制器 本程序为接受程序根据此程序可增加遥控路数-Road 15 remote-control switch controller procedures for the acceptance of this procedure in accordance with this procedure can increase the remote control approach
    2022-08-17 15:45:27下载
    积分:1
  • === =时钟20:6=== === == 应先初始化状态寄存器 tx1714 EQU 7FFH PA EQU 05H PB EQU 0...
    === =时钟20:6=== === == 应先初始化状态寄存器 tx1714 EQU 7FFH PA EQU 05H PB EQU 06H PC EQU 07H PD EQU 20H IAR EQU 00H 间接寻址寄存器 TMR0 EQU 01H 定时器 STATUS EQU 03H 状态寄存器 BSR EQU 04H bank选择寄存器 PORTA EQU 05H I/0端口寄存器 PORTB EQU 06H I/0端口寄存器 PORTC EQU 07H I/0端口寄存器 PORTD EQU 20H I/0端口寄存器 PULL EQU 21H PULL-High上拉寄存器 WAKEUP EQU 22H 唤醒控制寄存器--被用来设定watchdog允许和禁止 IRQM EQU 23H 中断屏蔽寄存器 IRQF EQU 24H 中断标志寄存器 WDTSEL EQU 25H -=== === = clock 20 : 6 === === === == should first register initialization state tx1714 EQU 7FFH EQU PA PB EQU 05H 06H 07H PC EQU PD EQU 20H IAR E QU 00H indirectly addressable registers TMR0 EQU 01H timer STATUS EQU Mr send state BSR EQU-deposit bank in the 04H choice Register PORTA EQU 05H I/O ports Register P ORTB EQU 06H I/O ports Register PORTC EQU 07H I/O ports Register POR TD EQU 20H I/O ports Register PULL EQU 21H PULL-High pull Register WAKEUP EQU 22H awaken control registers-- were used to set watchdog allowed and prohi
    2022-03-18 22:55:02下载
    积分:1
  • 开关稳压电源 开关稳压电源
    开关稳压电源 开关稳压电源-Switching Power Supply Switching Power Supply
    2022-04-20 10:10:42下载
    积分:1
  • 这个小实用程序有助于产生七段显示代码,为不同的我。
    This small utility helps to generate seven segment display codes for different I/O connections. For example, AVR/PIC Port A.0 -> D Segment Port A.1 -> B Segment .... Also it can generate Common Cathode or Common Anode table codes.. I Coded it long time ago. I Hope help someone. Thank you
    2022-08-02 23:48:22下载
    积分:1
  • 万年历 megal128 iccavr开发平台
    万年历 megal128 iccavr开发平台-Calendar megal128 iccavr development platform
    2022-03-18 16:21:04下载
    积分:1
  • 696518资源总数
  • 106182会员总数
  • 24今日下载