-
通过键盘设定温度和加热时间。
（2）使用DS18B20采集温度，采用七段数码管显示当前温度和剩余时间，并和设置的温度进行比较。
（3）当温度低于设定值时...
通过键盘设定温度和加热时间。
（2）使用DS18B20采集温度，采用七段数码管显示当前温度和剩余时间，并和设置的温度进行比较。
（3）当温度低于设定值时，通过DAC0832输出电压供给发热电阻RT1,使其温度升高。
-Through the keyboard setting temperature and heating time. (2) The use of DS18B20 collecting temperature, using seven-segment digital tube displays the current temperature and the remaining time, and and set the temperature for comparison. (3) When the temperature is below the set value, the DAC0832 output voltage of the supply of heat through the resistor RT1, so that temperature.
- 2022-09-26 00:55:03下载
- 积分：1
-
C language programming of embedded systems practice. Pdf of a person of great he...
C语言嵌入式系统编程修炼.pdf 对作嵌入式得人很有帮助-C language programming of embedded systems practice. Pdf of a person of great help for the embedded
- 2022-02-16 09:11:03下载
- 积分：1
-
s document describe davicom ic dm9000 DM9000_h.h . this ic can be used in the em...
s document describe davicom ic dm9000 DM9000_h.h . this ic can be used in the embedded systems and network lan cards. its is 10/100Mpbs ic.
- 2022-02-24 14:25:04下载
- 积分：1
-
MIPS Assembly Language Programming
MIPS Assembly Language Programming
- 2023-05-19 21:10:03下载
- 积分：1
-
数字访客计数器
应用背景数字访客计数器是一个可靠的电路在房间里的人数，人数/访客的任务准确地。当有人进入那房间的计数器一。房间内的人总人数在液晶屏上显示。微控制器做上述工作。它接收来自传感器，这个信号是在软件的控制下运行的存储在闪存中。您可以重置计数器使用复位开关。关键技术Keil IDE8051单片机红外传感器接口P89V51RD2液晶jhd162a
- 2023-03-08 17:20:04下载
- 积分：1
-
12232液晶显示器的驱动程序，供大家好好参考
12232液晶显示器的驱动程序，供大家好好参考-12232 LCD display driver, a good reference for everyone
- 2022-03-12 20:59:44下载
- 积分：1
-
I2C ： 用C语言编译的I2C，希望大家喜欢
I2C ： 用C语言编译的I2C，希望大家喜欢-I2C: use of C language compilers of I2C, hope you like
- 2022-06-20 01:18:44下载
- 积分：1
-
AT29C040 literacy source
AT29C040读写源程序-AT29C040 literacy source
- 2022-08-11 23:57:30下载
- 积分：1
-
在uclinux使用jffs 很不错的
在uclinux使用jffs 很不错的-use the Basis jffs very good Dongdong
- 2022-06-20 20:11:11下载
- 积分：1
-
Xilinx IIC IP
由 Xilinx 提供的 IIC 接口，使用 AXI interface。
Features
‧ AXI interface is based on the AXI4-Lite interface
‧ Master or slave operation
‧ Multi-master operation
‧ Software selectable acknowledge bit
‧ Arbitration lost interrupt with automatic mode switching from master to slave
‧ Calling address identification interrupt with automatic mode switching from master to slave
‧ START and STOP signal generation and detection
‧ Repeated START signal generation
‧ Acknowledge bit generation and detection
‧ Bus busy detec
‧ Fast mode 400 KHz operation or standard mode 100 KHz
‧ 7-bit or 10-bit addressing
‧ General call enable or disable
‧ Transmit and receive FIFOs - 16 bytes deep
‧ Throttling
‧ General purpose output, 1 bit to 8 bits wide
‧ Dynamic Start and Stop generation
‧ Filtering on the SCL and SDA signals to eliminate spurious pulses
- 2023-09-07 01:15:03下载
- 积分：1
