登录
首页 » 嵌入式系统 » TMC260驱动

TMC260驱动

于 2022-11-13 发布 文件大小:1.20 kB
0 166
下载积分: 2 下载次数: 1

代码说明:

主机为STM32,TMC260的初始化配置,正确配置后才能驱动步进电机,注意CS信号不能缺省

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • 这是早期MiniGUI DOS版本的最终版,压缩包内包含源代码、示例程序和API参考文档。该版本适合初学者,在BC++4。5上可直接编译,本人正试图将其移植到u...
    这是早期MiniGUI DOS版本的最终版,压缩包内包含源代码、示例程序和API参考文档。该版本适合初学者,在BC++4。5上可直接编译,本人正试图将其移植到uclinux中。-early MiniGUI This is the ultimate version of DOS version, compressed packet contains source code, sample program and API reference documentation. The version for beginners, the BC++4. 5 can be directly translated, I was trying to migrate to its Basis China.
    2022-01-25 14:04:15下载
    积分:1
  • stm32自学源码
    自己总结的一些源码,而且每个.h文件都有实验用的主函数,只需烧录到单片机就可以使用,对初学者有很大帮助。
    2022-01-26 08:29:51下载
    积分:1
  • STM32 IAP在线远程升级
    资源描述 资源描述 1.硬件使用的是STM32F407的平台, 2.通过GPRS实现远程IAP升级,使用的是标准ymodem传输协议, 3.编译工具MDK4.7,代码已经调试通过。
    2022-01-25 22:45:21下载
    积分:1
  • Michael J. Pont 的编程讲座1, 8051CPU,keil开发环境。英文的,通俗易懂。...
    Michael J. Pont 的嵌入式系统编程讲座1, 8051CPU,keil开发环境。英文的,通俗易懂。-Michael J. Pont Embedded Systems Programming Lecture 1,8051 CPU, keil development environment. English, user-friendly.
    2022-03-19 10:03:25下载
    积分:1
  • PPP ucIP源代码
    ppp source code for ucip
    2022-07-25 04:50:45下载
    积分:1
  • ARM Boot 程序源码 1.1.0armboot
    ARM Boot 程序源码 1.1.0armboot-1.1.0 希望给你带来方便-ARM Boot procedures 1.1.0armboot source-1.1.0 want to give you the convenience of
    2022-09-19 02:25:03下载
    积分:1
  • MF2001NT半自动包装秤资料汇总
    详细讲述MF2001NT半自动包装秤资料汇总(2011.3)使用以及方法。
    2022-12-30 18:30:03下载
    积分:1
  • arm单片机的串口升级程序
    基于Cortex-M3的NXP公司的LPC1766的单片机IAP串口升级程序bootloader,可通过串口升级单片机中的程序
    2022-12-18 13:35:03下载
    积分:1
  • Xilinx IIC IP
    由 Xilinx 提供的 IIC 接口,使用 AXI interface。 Features ‧ AXI interface is based on the AXI4-Lite interface ‧ Master or slave operation ‧ Multi-master operation ‧ Software selectable acknowledge bit ‧ Arbitration lost interrupt with automatic mode switching from master to slave ‧ Calling address identification interrupt with automatic mode switching from master to slave ‧ START and STOP signal generation and detection ‧ Repeated START signal generation ‧ Acknowledge bit generation and detection ‧ Bus busy detec ‧ Fast mode 400 KHz operation or standard mode 100 KHz ‧ 7-bit or 10-bit addressing ‧ General call enable or disable ‧ Transmit and receive FIFOs - 16 bytes deep ‧ Throttling ‧ General purpose output, 1 bit to 8 bits wide ‧ Dynamic Start and Stop generation ‧ Filtering on the SCL and SDA signals to eliminate spurious pulses
    2023-09-07 01:15:03下载
    积分:1
  • 印制电路板(PCB)及PowerPCB简介.doc
    印制电路板(PCB)及PowerPCB简介.doc -Printed circuit board (PCB) and PowerPCB profile. Doc
    2022-04-29 11:12:53下载
    积分:1
  • 696518资源总数
  • 105877会员总数
  • 14今日下载