登录
首页 » SCM » 液晶显示模块。在lcd上显示数字的函数。

液晶显示模块。在lcd上显示数字的函数。

于 2022-11-22 发布 文件大小:1.47 kB
0 121
下载积分: 2 下载次数: 1

代码说明:

液晶显示模块。在lcd上显示数字的函数。-display of the lcd

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • 用8051控制DDS信号发生器,产生1HZ
    用8051控制DDS信号发生器,产生1HZ-10MHz的正弦波/三角波/方波-DDS with 8051 control signal generator, producing the 1HZ-10MHz sine/triangle/square wave
    2022-06-27 09:07:28下载
    积分:1
  • 电荷转移容性触摸按键传感器示例代码,这是基于C8051F的,很容易移植到其他平台!...
    电荷转移容性触摸按键传感器示例代码,这是基于C8051F的,很容易移植到其他平台!-Charge-transfer capacitive touch sensor button sample code, which is based on the C8051F easily ported to other platforms!
    2022-03-06 16:43:15下载
    积分:1
  • 20*2液晶驱动程序,可以以总线方式或间接控制方式,注释清楚明了...
    20*2液晶驱动程序,可以以总线方式或间接控制方式,注释清楚明了
    2022-01-20 23:01:24下载
    积分:1
  • 用于单片机32bit内的快速开方(C51)
    用于单片机32bit内的快速开方(C51)-32bit MCU for the rapid evolution (C51)
    2022-06-21 07:57:56下载
    积分:1
  • LCD module times expected 12,864 Chinese
    液晶模块12864中文次料-LCD module times expected 12,864 Chinese
    2022-02-01 19:15:25下载
    积分:1
  • 结合温度传感器的实现测温度的C程序 这个小项目用到了比较多的AVR单片机的资源 是个不错的学习例程...
    结合温度传感器的实现测温度的C程序 这个小项目用到了比较多的AVR单片机的资源 是个不错的学习例程-Realize the combination of temperature sensor measuring the temperature of the C program that uses a relatively small projects and more resources AVR MCU is a good learning routines
    2023-06-11 15:05:08下载
    积分:1
  • 51单片机C语言应用程序实例精讲,讲解了大量51单片机的应用知识,并附有程序和电路图....
    51单片机C语言应用程序实例精讲,讲解了大量51单片机的应用知识,并附有程序和电路图.-51 Single-chip C language application instance精讲, on a large number of 51 single-chip application of knowledge, together with the procedures and circuit diagrams.
    2022-11-13 10:45:04下载
    积分:1
  • keil C51 Portable事例
    keil C51 Portable事例-Portable stories
    2022-02-05 15:54:36下载
    积分:1
  • 测试温度和湿度以及烟雾报警器,硬件应使用…
    测试温湿度以及烟感报警,硬件采用长应8000系列-Test temperature and humidity as well as the Smoke Alarm, hardware should be used long-8000 Series
    2022-07-22 09:10:03下载
    积分:1
  • MCS
    MCS-51单片机有5个中断源,其中两个是由-INT0、-INT1引脚输入的外部中断源;另外三个是内部中断源即由T0、T1的溢出引起中断和串行口发送完一个字节或接收到一个字节数据引起中断。触发外部中断有两种方式,即下降沿引起中断或低电平引起中断。当编程TCON中的ITi(i=0、1)为1时,则引起触发的方式为边沿触发方式,反之(ITi=0)为低电平触发方式。每个中断源的中断请求能否得到响应要受两级“开关”的控制,即一个总“开关”-MCS-51 single-chip has five interrupt sources, two of which are by-INT0,-INT1 pin input external interrupt source the other three internal interrupt sources from the T0, T1 overflow caused by the disruption and serial port sending or receiving end of a byte to a byte of data caused by interruption. Triggered external interrupt has two modes, namely, falling edge or low-level disruption caused disruption caused. When programming TCON in ITi (i = 0,1) for the 1:00 has been the subject of a way to trigger the way to the edge of the trigger, on the contrary (ITi = 0) for low-level trigger mode. Each interrupt source interrupt request can be subject to levels in response to
    2023-07-06 00:00:03下载
    积分:1
  • 696518资源总数
  • 105964会员总数
  • 17今日下载