登录
首页 » Verilog » 256分16位FFT

256分16位FFT

于 2022-12-04 发布 文件大小:23.94 MB
0 182
下载积分: 2 下载次数: 1

代码说明:

应用背景256、分 ;  16;FFT执行一个基2快速傅里叶变换FFT架构。在一个等级的基础上,每一个等级都有自己的蝴蝶和等级,并用记忆从彼此分离交织器。 ;该FFT可以执行calcualations关于连续和数据流的数据(一个数据一套接一个的),多了,输入和输出通过对,增加带宽加倍。并;关键技术256、分 ;  16;FFT

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • RISC-V-Reader-Chinese-v2p1
    说明:  RISC-V手册 最新版 一本开源指令集的指南 我们打算将这本薄薄的书作为 RISC-V的介绍和参考 资料 ,供有兴趣编写 RISC-V代码的 学生和嵌入式系统程序员使用 。 本书假设读者事先已经 了解 过至少一个指令集。如果没 有,您可能希望浏览基于 RISC-V的相关入门架构手册: Computer Organization and Design RISC-V Edition: The Hardware Software Interface。(risc v reader chinese)
    2020-05-07 10:58:23下载
    积分:1
  • sd_slave_device
    verilog source code for SD card SLAVE DEVICE IP-Core
    2021-04-12 22:18:56下载
    积分:1
  • AHB-answers
    这个文档回答了很多关于AHB总线在使用上经常遇到的问题(this doc gives a lot of answers for using AHB bus when doing design)
    2020-10-21 12:17:24下载
    积分:1
  • fullbridge_double_frequency
    建立了单相的PWM整流器电路闭环控制的仿真模型。版本R2007(The simulation model of the closed-loop control of single-phase PWM rectifier circuit. Version R2007)
    2021-02-02 09:10:00下载
    积分:1
  • hilbert_m
    基于FPGA的希尔伯特变化的verilog代码(Hilbert change verilog code)
    2020-10-19 09:37:25下载
    积分:1
  • iifftt
    说明:  verilog实现的fft算法,其中还有ifft算法(FFT algorithm based on Verilog)
    2020-09-20 00:57:52下载
    积分:1
  • 设计 verilog 蓝牙模块
    蓝牙是一种标准协议的设备 (如手机、 掌上电脑、 个人电脑和任何其他设备之间的无线连接。这一标准的主要目的是提供免版税标准这种无线协议。这个项目的目标是打造 HCI LMP,开源免费蓝牙基带控制器和高层次软件栈
    2022-01-21 00:55:09下载
    积分:1
  • tcp_ip_core_w_dhcp_latest.tar
    以太网协议 TCP/IP/DHCP协议verilog实现(Ethernet IP/TCP/DHCP verilog source code)
    2018-08-23 14:35:01下载
    积分:1
  • fffffff
    如上图所示, Rst是低电平有效的系统复位信号,Clk是时钟信号。AB[5:0]是地址信号,DB[7:0]是数据信号,wr是低电平有效的写信号。start是启动信号。 模块中有一个64x8的双端口的存储器。系统复位结束后,可以通过AB、DB和wr信号向同步存储器写入数据。当写入64个数据后,给出一个Clk周期宽度的脉冲信号start,则系统从存储器0地址处开始读出数据,读出的8位数据从低位开始以3位为一组,每个时钟周期输出一组,即第一个时钟周期输出[2:0]位,第二个时钟周期输出[5:3]位,第三个周期输出1地址的[0]位和0地址的[7:6]位,直至将存储器中64x8数据全部输出。若最后一组不足三位,则高位补0。 (As shown above, Rst is an active-low system reset signal, Clk is a clock signal. AB [5: 0] is the address signal, DB [7: 0] is the data signal, wr write signal is active low. start is the start signal. Module in a dual port memory of 64x8. After the reset, you can write data to the synchronous memory by AB, DB and wr signals. When data is written to 64, given the width of a pulse signal Clk cycle start, the system begins to read the memory address 0, 8 data read out a low starting with three as a group, each clock outputs a set period, which is the first clock cycle of the output [2: 0] bits, the second clock cycle output [5: 3] position, the third cycle of the output of an address [0] and 0 address [7 : 6] bit, until all the data in memory 64x8 output. If the last group of less than three, the high 0s.)
    2020-11-04 20:39:51下载
    积分:1
  • vga
    说明:  实现在屏幕上显示绿色和红色相间的水平条纹。其中,vga_640x480模块将产生行同步信号hsyn和场同步信号 vsync; vga_stripes模块将产生red、green和blue三个输出。(The horizontal stripes of green and red are displayed on the screen. Among them, vga_640x480 module will produce line synchronization signal Hsyn and field synchronization signal vsync; vga_stripes module will produce red, green and blue three outputs.)
    2020-06-24 02:00:02下载
    积分:1
  • 696516资源总数
  • 106783会员总数
  • 25今日下载