-
digital clock display procedures and an examination revealed that the procedures...
数字钟的显示程序以及一个检验显示的程序，用在8051或8031-digital clock display procedures and an examination revealed that the procedures used in 8051 or 8031
- 2022-03-18 19:16:20下载
- 积分：1
-
单片机标准键盘PS2与单片机通信这是用C语言写 的哈
单片机标准键盘PS2与单片机通信这是用C语言写 的哈-MCU standard keyboard PS2 and SCM communication is written in C language in Kazakhstan
- 2022-02-03 20:05:41下载
- 积分：1
-
18B20温度传感器的单片机程序，检测当前环境温度并将温度数据返回到单片机。...
18B20温度传感器的单片机程序，检测当前环境温度并将温度数据返回到单片机。-Single-chip temperature sensor 18B20 procedure, testing the current ambient temperature and the temperature data back to the single chip.
- 2022-01-22 04:28:14下载
- 积分：1
-
在LASG发现梯度迪图
grads ditu find in lasg-grads cnriver & cnprovince
- 2022-01-31 15:10:54下载
- 积分：1
-
用ATMEGA8开发的MMC程式,可用AVR
用ATMEGA8开发的MMC程式,可用AVR-GCC开发-with ATMEGA8 development of the MMC programs, available AVR-GCC Development
- 2022-02-28 11:30:40下载
- 积分：1
-
太阳能热水器方案详细信息，包括一个标志
太阳能热水器方案详情，包括标牌和登记册详情
- 2022-07-11 09:54:31下载
- 积分：1
-
ATmega16 procedures, controls 1602 LCD with only six I/O ports, I' ve simulat...
ATmega16程序，控制1602液晶，只用了六个I/O口，我仿真过的，没有错误，而且还带Pretues图。-ATmega16 procedures, controls 1602 LCD with only six I/O ports, I" ve simulation, there are no errors, but also with Pretues map.
- 2022-07-06 12:02:41下载
- 积分：1
-
IC Card operating software : AT88SCl604 chip mode of operation there are five. T...
IC卡操作软件:AT88SCl604芯片的操作模式有五种。它们是通过配PGM、RST、CLK等引脚信号及内部地址计数器(IAC)的状态组合来实现。 (1) 芯片复位操作： AT88SCl604有两种复位方式:上电复位和控制复位。 上电复位： 上电复位是当芯片加电时的最初状态。上电复位属于芯片 内部复位。它将使芯片内部所有的隐含标志复位到"0"状态。并使地址计数器复位到0位。 控制复位： 当CLK为低时，在RST脚上的一个下降沿将便芯片产生复位操作。 控制复位是将地址计数器复位到0位，而不影响任何内部标志的状态。-IC Card operating software : AT88SCl604 chip mode of operation there are five. They are allocated by PGM, RST, etc. pin CLK signal and the internal address counter (IAC) portfolio of the state is to be achieved. (1) chip reset operation : reduction AT88SCl604 two ways : power-on reset and reset control. Power-on reset : power-on reset when the chip is in power at the initial state. Power-on reset the internal chip is reset. It will enable all internal chip implied signs reset to "0" state. Make address counter reset to 0. Reset control : When the CLK for the low, the RST feet of a falling edge chips will have to reset operation. Reset control is to address counter reset to 0, without prejudice to any signs of internal sta
- 2022-05-28 08:23:00下载
- 积分：1
-
标准frescale单片机的I2C总线程序
标准frescale单片机的I2C总线程序-frescale MCU standard I2C bus procedures
- 2022-06-15 16:32:18下载
- 积分：1
-
s24193 液晶ARM，8051驱动程序！
s24193 液晶ARM，8051驱动程序！-s24193 LCD ARM, 8051 driver!
- 2022-05-21 08:13:58下载
- 积分：1
