登录
首页 » 通信 » 自动升级程序, 自动升级程序

自动升级程序, 自动升级程序

于 2022-12-20 发布 文件大小:3.23 MB
0 116
下载积分: 2 下载次数: 1

代码说明:

自动升级程序, 自动升级程序-Automatic escalation procedures, automatic escalation procedures

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • CDMA型参考系统
    CDMA TYPE REFFERENCE SYSTEMS - INTRODUCTION - IS-95 system - THIRD GENERATION SYSTEMS
    2022-12-21 09:15:03下载
    积分:1
  • 一个特别适用于单片机调试的用串口讯软件。可以发送和接受ASCII和HEX(二进制)代码,在MCU方式下自动转换Parity:发送地址时Parity=M,发送...
    一个特别适用于单片机调试的通用串口通讯软件。可以发送和接受ASCII和HEX(二进制)代码,在MCU方式下自动转换Parity:发送地址时Parity=M,发送数据Parity=S,同时可以定时发送数据。也可以作为通用串口调试工具。-a particularly applicable to the common debugging MCU serial communication software. Can send and receive ASCII and HEX (binary) code, the MCU mode automatically converted Parity : Send address Parity = M, send data Parity = S, and can send data regularly. GM also can be used as serial debugging tools.
    2023-04-15 05:20:03下载
    积分:1
  • 华为GTM900C程序代码
    #include "config.h" INT8U RBUF; INT8U TDAT,RDAT; INT8U TCNT,RCNT; INT8U TBIT,RBIT; BOOLEAN TING,RING; BOOLEAN TEND,REND; INT8U uc_rxdIndex,uc_rxdDealIndex; INT8U uc_uartBuf[UART_BUF_LEN]; INT8U uc_uartRecFifoLen; /* 接收FIFO中的数目 */ BOOLEAN b_uartRecFifoFlag; INT16U us_allSendCnt; INT8U uc_sendCnt; //INT8U * pSendBuf; INT8U * p_pSendBuf[P_SEND_BUF_LEN]; /* 要发送的数据的指针 */ INT8U uc_pSendBufLen[P_SEND_BUF_LEN]; /* 每个指针包含的数据长度 */ INT8U uc_pSendBufIndex; INT8U uc_pSendBufDealIndex;
    2022-02-21 22:52:47下载
    积分:1
  • Send message code, has to verify the steps to send one: Download javacomm20
    短信发送代码,已经验证可以发送 步骤一:下载javacomm20-win32.zip 步骤二:com4端口上接上GSM猫,或者改变源代码 OK-Send message code, has to verify the steps to send one: Download javacomm20-win32.zip Step 2: com4 port connected to GSM cats, or changing the source code OK
    2022-12-06 22:40:03下载
    积分:1
  • 收发传真,浏览传真的程序
    收发传真,浏览传真的程序-A program which receive、send and scan fax
    2022-08-08 03:01:15下载
    积分:1
  • AES安全
    AES安全通信的软件,由于网络的不安全,好多通信可能被窃取,因此此软件可以实现安全通信。
    2022-06-16 04:00:50下载
    积分:1
  • 互动.NET单用户留言簿
    互动.NET单用户留言簿-interaction.NET single-user Guestbook
    2023-03-06 11:20:03下载
    积分:1
  • 一套程序处理和管理 NetFlow 流工具
    流工具是一套程序来处理和管理 NetFlow 出口从思科和杜松的路由器。该软件最初是由 Mark Fullmer 而在俄亥俄州大学工作。Steve 罗米格和 OSU 的网络安全小组已添加文档、 功能,和提供的反馈。近来资助了 OARnet 和俄亥俄州印度我添加版本 8 PDU 支持和各种其他功能的时间。 安装注意事项及快速的入门,请参阅安装。 如果您正在使用流工具请订阅通过邮寄列表 向 flow-tools-request@splintered.net 发送一条消息 流工具是目前 http://www.splintered.net/sw/flow-tools
    2022-12-12 02:00:03下载
    积分:1
  • 三菱FX系列讯程序,可实现PC机与PLC的讯,在PC机上监控PLC运行状态...
    三菱FX系列通讯程序,可实现PC机与PLC的通讯,在PC机上监控PLC运行状态-Mitsubishi FX series of communications, which enables PC and PLC communications, the PC monitor PLC Operation
    2022-11-02 09:45:03下载
    积分:1
  • The use of MODBUS communications with EMA smart meter to receive information, we...
    利用MODBUS与EMA智慧型电表通讯,达到接收资料,希望对大家有所帮助。-The use of MODBUS communications with EMA smart meter to receive information, we hope to be helpful.
    2022-02-25 18:53:24下载
    积分:1
  • 696518资源总数
  • 106161会员总数
  • 5今日下载