登录
首页 » 汇编语言 » 红外线数据通信系统开发,汇编语言,Keil C51开发环境

红外线数据通信系统开发,汇编语言,Keil C51开发环境

于 2022-12-24 发布 文件大小:17.18 kB
0 254
下载积分: 2 下载次数: 1

代码说明:

红外线数据通信系统开发,汇编语言,Keil C51开发环境-Infrared data communication system development, assembly language, Keil C51 Development Environment

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • the source for the CPU PIC16C54 to adopt cost
    这个源码的CPU为PIC16C54,为子节约成本采用端口复用。-the source for the CPU PIC16C54 to adopt cost-saving portal reuse.
    2022-03-19 18:17:18下载
    积分:1
  • 设计多字节减法运算程序,要求程序能显示运算数据和结果数据(16进制)....
    设计多字节减法运算程序,要求程序能显示运算数据和结果数据(16进制).-design of multi-byte subtraction Operational procedures, requirements Operational procedures can show that the data and results data (16 bases).
    2022-06-27 12:13:22下载
    积分:1
  • 实例 好的很!
    汇编语言实例 好的很!-assembly language is a good example!
    2022-02-28 19:53:55下载
    积分:1
  • Beihang assembly language teaching materials, based on after
    北航的汇编语言教材,基于arm体系的课后实验源码。-Beihang assembly language teaching materials, based on after-school experimental arm system source code.
    2022-01-25 23:52:33下载
    积分:1
  • sad
    sad
    2022-08-22 16:44:16下载
    积分:1
  • 写的windows菜单例子2
    汇编写的windows菜单例子2-Compilation of written examples of windows menu 2
    2022-03-21 17:56:28下载
    积分:1
  • 利用实现一个可以在显示器上显示时、分、秒的电子时钟,并能提供整点报时功能。设计一个基本的具有显示时、分、秒的电子时钟。 到整点或预定的报警时间,能够...
    利用汇编语言实现一个可以在显示器上显示时、分、秒的电子时钟,并能提供整点报时功能。设计一个基本的具有显示时、分、秒的电子时钟。 到整点或预定的报警时间,能够以不同的音乐进行报时,可以自行设置闹钟报警时间; 实物演示时要求讲出程序原理和设计思想; 程序运行良好、界面清晰。 -The use of assembly language implementation on a show in the display hours, minutes and seconds of electronic clock, and can provide the whole point timekeeping function. Designed with a basic display hour, minute, second electronic clock. The whole point of the book or the alarm time, be able to carry out a different time in music, you can set their own alarm clock time kind demonstration program called the principle of speaking the idea and design program is running good, clear interface.
    2022-05-07 23:11:00下载
    积分:1
  • homemade clocks and clock interrupt handling procedures in the establishment of...
    自制时钟及时钟中断处理程序的编制 在CMD下运行,在右上角将出现当前的时间,同时可以输入CMD下的各种命令 相当于把单任务的操作系统改成多任务(一个显示时间,一个处理各种命令)-homemade clocks and clock interrupt handling procedures in the establishment of CMD running, in the upper right-hand corner there will be the current time, CMD also can be imported under the order amounts to a single task into multi-task operating system (a show, deal with a variety of orders)
    2022-01-22 09:07:33下载
    积分:1
  • ,片选接到p1.5 复位端 p1.4 中断端接到 int0 82c250工作在斜率模式下 ,RS 接51k电阻到地。 2,SJA10...
    ,片选接到p1.5 复位端 p1.4 中断端接到 int0 82c250工作在斜率模式下 ,RS 接51k电阻到地。 2,SJA1000与82C250的接口,逻辑上为SJA1000输出0(显性位),表现为低点平输出给82C250,则82C250输出 差分的低电平。SJA1000输出1(隐性位),表现为高电平或悬空输出给82C250,则82C250输出悬空状态。 3,周立功的中SJA_BCANCONF.ASM中对输出控制寄存器 的TX0的输出 极性的位的定义不对。 还有里面定义有接收错误标志码,不知道何时用。-, The election received a P1.5-chip client p1.4 interrupt reset int0 82c250 client received in the slope mode, RS then 51k resistor to ground. 2, SJA1000 with the 82C250 interface, logic for SJA1000 Output 0 (dominant bit), showing low level output to the 82C250, while the low-level differential output 82C250. SJA1000 Output 1 (recessive), and the performance of the output is high or left vacant to the 82C250, the vacant state 82C250 output. 3, Zhou Ligong in the SJA_BCANCONF.ASM of output control register TX0 output polarity bit the definition of wrong. Inside the definition also has to receive error flag code, I do not know when to use.
    2022-06-28 07:07:40下载
    积分:1
  • LPC2000 启动代码Start.s文件简要分析
    LPC2000 启动代码Start.s文件简要分析 先说一下启动代码的位置,启动代码是在板子加电后首先执行的。所以非要用汇编来写才行。 要完成处理器模式的初始化、设置中断向量表、设置各个模式下的堆栈、初始某些变量从而把 系统带到一个合适的运行环境中开始用户程序的运行。 本段设置处理器的模式相关常量
    2023-08-02 02:00:02下载
    积分:1
  • 696516资源总数
  • 106571会员总数
  • 2今日下载