-
LPC2103, beep gas compiler, very good use, IAR environment
LPC2103,蜂鸣气编译程序，很好用，IAR环境下-LPC2103, beep gas compiler, very good use, IAR environment
- 2022-07-23 05:10:28下载
- 积分：1
-
AD series fft Transform
AD系列fft变换-AD series fft Transform
- 2022-03-04 21:50:58下载
- 积分：1
-
延时采用指令延时的方法,通过改变系统时钟,改变延时的长短,用IOA口的低8位接的LED的闪烁显示出来...
延时采用指令延时的方法,通过改变系统时钟,改变延时的长短,用IOA口的低8位接的LED的闪烁显示出来-Delay the use of methods of instruction latency by changing the system clock, changing the length of delay, and low IOA I received 8 of the LED display flashes
- 2022-01-26 02:06:17下载
- 积分：1
-
最近作的AD9852的FM扫频模式，自动计算频率，采用单片机的总线访问方式，非常方便，你要做 的就是填数...
最近作的AD9852的FM扫频模式，自动计算频率，采用单片机的总线访问方式，非常方便，你要做 的就是填数-Recently, the AD9852 for the FM sweep mode, automatic calculation of the frequency of the use of single-chip bus access method, a very convenient, you have to do is fill in a few
- 2022-05-25 07:24:40下载
- 积分：1
-
This procedure is the next dual
本程序是下个双通道充电器的原程序,充两节NI-MH电池,-This procedure is the next dual-channel charger for the original procedure, two rechargeable NI-MH battery,
- 2022-02-06 13:32:13下载
- 积分：1
-
这是一个与PIC采用SD卡的源代码
this is a source code for usinf sd card with PIC
- 2023-02-10 17:15:03下载
- 积分：1
-
热电偶测温误差分析 论文
针对工业加热炉，详细分析了热电偶测温过程。由于热电偶热端与炉墙内表面之间的辐射换热，以
及热电偶本身因热端和冷端温度不同造成...
热电偶测温误差分析 论文
针对工业加热炉，详细分析了热电偶测温过程。由于热电偶热端与炉墙内表面之间的辐射换热，以
及热电偶本身因热端和冷端温度不同造成的导热总是存在，因此热电偶测温存在误差。本文从理论上分析了
热电偶测温误差的来源，提出了热电偶测温误差计算模型，并导出了测温误差的近似计算公式，还结合实例讨
论了减小测温误差的措施。
- 2022-02-16 06:23:52下载
- 积分：1
-
At can be given its arguments in a file. You can comment
out lines by precedin...
At can be given its arguments in a file. You can comment
out lines by preceding them with either # or -
characters. This is an easy way to temporarily disable
some commands.
The CONTINUE-command is most useful at the end of the
file. When this command is read, the file is started
again from the beginning. You can use it situations where
the machine is not shut down for the night and you want
to run some commands every day.- At can be given its arguments in a file. You can comment
out lines by preceding them with either# or-
characters. This is an easy way to temporarily disable
some commands.
The CONTINUE-command is most useful at the end of the
file. When this command is read, the file is started
again from the beginning. You can use it situations where
the machine is not shut down for the night and you want
to run some commands every day.
- 2022-02-21 09:29:04下载
- 积分：1
-
MSP430单片机在一些自己收藏的一些有需要的人，请下载…
关于msp430单片机的一些
自己收集的一些有需要的请下载-MSP430 MCU on some of his own collection of some of those in need, please download
- 2022-04-30 08:31:10下载
- 积分：1
-
凌阳16位单片机的启动代码，它是源码，是凌阳的公司提供的
凌阳16位单片机的启动代码，它是源码，是凌阳的公司提供的-Sunplus 16-bit single-chip start-up code, it is the source code is provided by the company of Sunplus
- 2022-06-01 20:54:37下载
- 积分：1
