-
I2C总线程序,及读写24C04
I2C总线程序,及读写24C04-I2C bus procedures, and writing 24C04
- 2022-03-20 12:22:02下载
- 积分:1
-
关于51单片机红外解码的程序,解释详细,已编译过,可直接使用,并有HEX文件...
关于51单片机红外解码的程序,解释详细,已编译过,可直接使用,并有HEX文件-About 51 single-chip infrared decoding procedures, a more detailed explanation has been compiled can be used directly and HEX file
- 2022-08-11 16:57:48下载
- 积分:1
-
在单片机向实际系统发出控制信号时,需用数模转换芯片将数字信号转成模拟信号.这个程序和原理图详细说明了DA转换器的应用和开发....
在单片机向实际系统发出控制信号时,需用数模转换芯片将数字信号转成模拟信号.这个程序和原理图详细说明了DA转换器的应用和开发.-In SCM systems to the actual control signal, the required digital-to-analog converter chip digital signal into analog signal. This procedure and schematic diagram detailing the application of DA converters and development.
- 2022-03-18 15:30:19下载
- 积分:1
-
本书以采用89C52为核心的仿真实验板为主线,充分发挥该实验板不需仿真器就可在线调试和在线下载、成本低廉的特点,采取边练边学的指导思想,合理、有机地将单片机的原...
本书以采用89C52为核心的仿真实验板为主线,充分发挥该实验板不需仿真器就可在线调试和在线下载、成本低廉的特点,采取边练边学的指导思想,合理、有机地将单片机的原... -Book to the use of 89C52 as the core simulation board the main line, give full play to the board without emulator can be downloaded online debugging and on-line, low cost, take the side of practice to learn the guiding ideology, reasonable, will be organically the original single-chip ...
- 2022-02-03 14:33:40下载
- 积分:1
-
采用51系列单片机控制的I2C总线高频头程序源码.
采用51系列单片机控制的I2C总线高频头程序源码.-51 Series Single-chip I2C bus control procedures Tuner source.
- 2022-04-18 15:22:51下载
- 积分:1
-
步进电机控制,LCD显示
步进电机控制,LCD显示-Stepper motor control, LCD display
- 2022-12-06 09:25:03下载
- 积分:1
-
完整的TCS控制系统原程序.包含系统检测,数据采集(A-D)与处理,通信和回路控制与检测.产品已上市....
完整的TCS控制系统原程序.包含系统检测,数据采集(A-D)与处理,通信和回路控制与检测.产品已上市.-integrity of the original control system procedures. Includes system testing, data acquisition (A-D) and processing, communication and loop control and detection. Products are listed.
- 2022-06-28 09:59:38下载
- 积分:1
-
关于msp430单片机的一些
自己收集的一些有需要的请下载
关于msp430单片机的一些
自己收集的一些有需要的请下载-MSP430 MCU on some of his own collection of some of those in need, please download
- 2022-01-26 06:56:29下载
- 积分:1
-
6段数码管分别显示,时,分,秒,四个按键,K1(P0.0),K2(P0.1),
K3(P0.2),K4(P0.3),四个按键用来调时间的,按下K1,所有位都...
6段数码管分别显示,时,分,秒,四个按键,K1(P0.0),K2(P0.1),
K3(P0.2),K4(P0.3),四个按键用来调时间的,按下K1,所有位都清零显示,然后按下K2,秒在闪烁,继续按K2分闪烁,不段地按K2 秒--分--时切换着闪烁,在某位闪时按下K3相应位加一,确认调整,按K4,取消调整再按K1。在K1按下以后才有调时的功能,如果K1没有按下,按别的键没有反映。这为了在加点按键功能留着用
-6 respectively of the digital control, when, minutes and seconds, four keys, K1 (P0.0). K2 (P0.1), K3 (P0.2), K4 (width), the four keys to the transfer time, press the K1, All spaces are reset, then press K2, the scintillation seconds, according to K2 pm flickered. not according to K2 of seconds-- minutes-- when switching to flicker in certain press the flash-K3 corresponding increase in a confirmed adjustment by K4, then canceled K1 adjustment. K1 in the press will only be made after the transfer of function, if K1 pressed by other key is not reflected. This points to the function keys used Retention
- 2022-08-13 14:18:02下载
- 积分:1
-
nRF2401快速开发系统相关的帮助文档。
nRF2401快速开发系统相关的帮助文档。-nRF2401 rapid development of systems related to the help document.
- 2022-02-21 19:17:21下载
- 积分:1