-
12864+ Ds1302 the perpetual calendar, LCD is intended to bring the Chinese font,...
12864+ds1302 的万年历，LCD是带中文字库的，串行-12864+ Ds1302 the perpetual calendar, LCD is intended to bring the Chinese font, serial
- 2022-09-08 22:50:02下载
- 积分：1
-
MCS
MCS-51单片机实用子程序库（3），WORD文档-MCS-51 microcontroller practical Subroutine Library (3), the Word document
- 2023-05-17 03:00:03下载
- 积分：1
-
xc164cs_adc
xc164cs的AD转换程序
xc164cs_adc
xc164cs的AD转换程序-xc164cs_adcxc164cs the AD conversion process
- 2023-03-06 21:05:04下载
- 积分：1
-
at89s51，超级牛的教程，可以配合proteus仿真实验，
at89s51，超级牛的教程，可以配合proteus仿真实验，-at89s51, super tutorial cattle will be in line with Proteus simulation experiment,
- 2022-07-06 09:11:35下载
- 积分：1
-
89S51单片机上开发红外线遥控,开发环境KEIL C51,
89S51单片机上开发红外线遥控,开发环境KEIL C51,-89S51 developed single-chip infrared remote control, development environment KEIL C51,
- 2023-09-06 02:50:03下载
- 积分：1
-
利用脉冲控制伺服电机运转，伺服电机频率通过改变定时器初值来控制...
利用脉冲控制伺服电机运转，伺服电机频率通过改变定时器初值来控制-The use of pulsed operation of servo motor control, servo motors by changing the timer frequency to control the initial value
- 2022-03-18 02:46:57下载
- 积分：1
-
AT89C2051 microcontroller product manuals, a very detailed description of the AT...
AT89C2051单片机的产品手册，非常详细的说明了AT89C2051单片机的性能参数、结构和原理。-AT89C2051 microcontroller product manuals, a very detailed description of the AT89C2051 MCU performance parameters, structure and principle.
- 2023-02-18 14:00:04下载
- 积分：1
-
BasicCAN Driver
BasicCAN 驱动程序-BasicCAN Driver
- 2022-02-05 19:59:05下载
- 积分：1
-
单片机51环境下的字库代码122*32点阵的液晶显示
单片机51环境下的字库代码122*32点阵的液晶显示-under the font code 122* 32 dot-matrix LCD
- 2022-05-25 05:55:35下载
- 积分：1
-
1．熟悉硬件仿真工具KD30的使用。 2．修改样本程序 SAMP1a，使无论在计数或停止计数时，按 SW3 均对计数值清零，并停止计数。 3．编制一个秒表程序,...
1．熟悉硬件仿真工具KD30的使用。 2．修改样本程序 SAMP1a，使无论在计数或停止计数时，按 SW3 均对计数值清零，并停止计数。 3．编制一个秒表程序, 测试精度为0.1秒，按 SW1键启动计数，再按一次 SW1键停止计数。任何时候按 SW3 键停止计数，并对计数值清零。 4．按 SW1键后， 以 0.1 秒为单位开始计数，再按一次 SW1 键停止计数。若按 SW1 键时间超过2秒，则计数值清零，回到初始状态。-1. Familiar with the hardware simulation tool KD30 use. 2. Revised procedures SAMP1a samples, regardless of the count or counts at the end, according to SW3 numerical terms were right, reset, and stop counting. 3. Preparation of a stopwatch procedures, testing accuracy of 0.1 seconds, according to bond SW1 start counting, according to a key SW1 stopped counting. By SW3 any time to stop counting bond and reset the count. 4. By SW1 bond, after 0.1 seconds for start counting, according to a key SW1 stopped counting. If SW1 keys by the time more than two seconds, then reset the count and return to the initial state.
- 2023-08-01 05:40:03下载
- 积分：1
